- 更多网络例句与接触表面相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Real contact between two surfaces occurs only at the asperities, which resulted in the fact that the asperities in real contact carry high load and are prone to elasto-plastic deformation.
摩擦副接触表面的接触只发生在极少数微凸体上，导致这些微凸体承受了较大的载荷，极易产生弹塑性变形。
-
If an object sliding along the contact surface, the two of the contact surface of the convex part of the collision, a fracture, wear, created obstacles to the movement.
如果一个物体滑动沿接触表面来看，两者的接触面的凸角部分的碰撞，断裂，磨损，制造障碍，把运动。
-
The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.
理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。
-
The influences of exciting force and initial normal load were investigated in detail. The curve of the tangential contact stiffness for variable normal preload was obtained by fitting the results according to the given condition.
利用该试验系统能够对不同初始正压力和激振力作用下接触表面间微幅相对运动的迟滞曲线进行测试，根据测试结果计算得到接触表面间的接触刚度。
-
As it hits the surface .a small amount of material is sputtered or dislodged from the surface.
当接触表面时。少数材料会从表面飞溅或喷出。
-
In order to prolong the service life of roller bearing, a deep end-cavity roller is applied to roller bearing of cone bits.
国内现有牙轮钻头滚动轴承多采用短圆柱滚子轴承结构，滚子边缘处存在应力集中现象，使得轴承接触表面极易发生疲劳破坏，为提高牙轮钻头滚动轴承抗接触疲劳寿命，提出在牙轮钻头滚动轴承中采用凹端圆柱滚子的方案。
-
In China, the roller bearing cone bit is now equipped with short cylindrical roller, which has stress centralization on the edge, and it easily causes fatigue failure on the contact area.
国内现有牙轮钻头滚动轴承多采用短圆柱滚子轴承结构，滚子边缘处存在应力集中现象，使得轴承接触表面极易发生疲劳破坏，为提高牙轮钻头滚动轴承杭接触疲劳寿命，提出在牙轮钻头滚动轴承中来用凹端圆柱滚子的方案。
-
In China, the roller bearing cone bit is now equipped with short cylindrical roller, which has stress centralization on the edge, and it easily causes fatigue failure on the contact area.
国内现有牙轮钻头滚动轴承多采用短圆柱滚子轴承结构，滚子边缘处存在应力集中现象，使得轴承接触表面极易发生疲劳破坏，为提高牙轮钻头滚动轴承抗接触疲劳寿命，提出在牙轮钻头滚动轴承中采用凹端圆柱滚子的方案。
-
Based on geometrical and physics optics, the principle of light scattering method to measure surface roughness was analyzed. The mirror and diffraction model were set up which show there is a quantitatively corresponding relationship between light's intensity distribution of reflected flare—light scattered band and surface roughness parameters.
作者通过对光学非接触表面粗糙度、微位移测量单元技术进行分析，确定以结构简单、测量速度快的光散射法测量表面粗糙度；以光散射法测量表面粗糙度和光学三角法测量微位移这两种不同工作原理和功能的光电传感器作为集成对象，使二者实现相同光源、相同光路、相同光敏接收器的光电传感器集成。
-
Thus different mediums have been used between the two contact surfaces in order to investigate the variations in the normal force with the feeding level under both adhesive- and non-adhesive-contact.
利用以等色序条纹技术为核心的表面力仪，使2个分子级光滑的圆柱状云母表面在一定载荷下接触，测量其接触区尺寸和接触表面的变形情况。
- 更多网络解释与接触表面相关的网络解释 [注：此内容来源于网络，仅供参考]
-
contact aerator：接触曝气池
consumption curve 消费曲线 | contact aerator 接触曝气池 | contact area 接触表面
-
contacting surface asperity：接触表面不平度
contacting sedimentation tank 接触沉淀罐 | contacting surface asperity 接触表面不平度 | contactolite 接触变质岩
-
contact area：接触表面
contact aerator 接触曝气池 | contact area 接触表面 | contact bed 接触滤床
-
contact surface：接触表面
contact pressure 接触压力 | contact surface 接触表面 | contactless pick up 无触点传感器
-
contact surface：接触表面=>接触面
contact support 端钮支架 | contact surface 接触表面=>接触面 | contact surface of valve seat 阀座接触面
-
contact surface number：接触表面数值
contact surface 接触(表)面 | contact surface number 接触表面数值 | contact tower 接触塔
-
contact surface separator：接触表面分离器
继电器伺服机构 contact servomechanism | 接触表面分离器 contact surface separator | 接触槽 contact tank
-
incident angle：入射角的声音或光线与其接触或通过的表面垂直线之间所形成的夹角
inch 英寸 | incident angle 入射角的声音或光线与其接触或通过的表面垂直线之间所形成的夹角 | incoming 引入的、输入的
-
pressure of contact surface：接触表面压力
pressure of air supply 送风压力 | pressure of contact surface 接触表面压力 | pressure of wind 风压
-
Ideal for measuring surface temperatures hard-to-reach, live areas：理想的测量表面温度难以接触到,生活领域
Features: 特点: | Ideal for measuring surface temperatures hard-to-reach, live areas理想的测量表面温度难以接触到,生活领域 | Targeting objects is easy with the bright laser beam针对的对象是容易的与光...