- 更多网络例句与挤压轮相关的网络例句 [注：此内容来源于网络，仅供参考]
-
On the basis of the analysis of cold extrusion process for the duralumin drive wheel,the scheme,the drawing and the blank dimension of cold extrusion were worked out.
对硬铝主动轮的冷挤压工艺进行分析，确定了冷挤压零件图和冷挤压方案及毛坯尺寸，对零件冷挤压的变形程度进行了校核，计算了挤压吨位，拟定了挤压前的毛坯处理规范，并对模具结构进行了介绍。
-
The staves of glue side, an increase of spine of clearance space whether it be binding line, or binding disc bicriterion, brush side adhesive are two copper-wheel excircle side extrusion, bookbinder controlof width on the side is the thickness of the copper round on both sides.
不正胶胶杠沉陷，补充了书脊间隙不时间无论是胶订联动线，还是胶订圆盘单机，刷不正胶都是通功两只铜轮边圆不正不不背的挤压来完不败的，胶订机上不正胶的阔度是两不正铜轮的薄度。
-
A macro and micro and chemical element analysis was made on fracture of ruptured coupling bolts,torsion test was performed and stress analysis and calculation were made,the results show that when the steam turbine had failure,MP-LP rotor coupling bolts and generator-exciter rotor coupling bolts failure were classified as overload shear fracture with partial deformation .
对215MW汽轮机断裂的对轮螺栓做断口宏观、微观分析，化学元素分析，扭转试验及受力分析计算，结果表明汽轮机组在事故中，中压-低压转子对轮螺栓和发电机-励磁机转子对轮螺柱的失效类型为：过载剪切断裂，同时局部挤压变形，这是由于事故过程中轴系受到冲击扭矩作用而引起的。
-
Open a spile , start an electric control valve motor when the job,control valve push in cam circular disc lower open up, lotus seed is followed by pressure to damaged shell knife , shell is cut apart thereupon and flesh is parted from the lotus for on causing a device to fall onto the squeezing claw squeezing a wheel under lotus seed classics, in squeezing a wheel rotating.
工作时，打开插板，启动电动机，控制阀在凸轮圆盘的推动下打开，莲子经下引装置落到挤压轮的挤压爪上，在挤压轮转动中莲子被压向破壳刀轨，于是壳被切开并与莲肉分离。关键的时候翻译不出来，大家帮忙先谢谢哈
-
Open a spile , start an electric motor when the job,control valve push in cam circular disc lower open up, lotus seed is followed by pressure to damaged shell knife , shell is cut apart thereupon and flesh is parted from the lotus for on causing a device to fall onto the squeezing claw squeezing a wheel under lotus seed classics, in squeezing a wheel rotating.
工作时，打开插板，启动电动机，控制阀在凸轮圆盘的推动下打开，莲子经下引装置落到挤压轮的挤压爪上，在挤压轮转动中莲子被压向破壳刀轨，于是壳被切开并与莲肉分离。关键的时候翻译不出来，大家帮忙先谢谢哈
-
Electrical Heating Upsetter; Air Hydraulic Flash Butt Welding Machine; Automatic Air-Hydraulic Pressure Seam Welder; Multi-...
双座电气加热挤压锻缩机；空油压式闪碰焊机；自动空油压轮焊机；多点式网类焊接机；螺母及螺丝自动。。。
-
In continuous extrusion forming process, the friction between the wheel groove and the feed is a driving force. The frictional energy and deformational energy change into heat, which makes the feed and the die's temperature field, strain field and stress field change.
在连续挤压成形过程中，挤压轮旋转，在变形体和模具接触面上的摩擦功和塑性变形功的作用下，变形体在塑性变形的同时，与模具及周围环境进行热交换，促使变形体和模具内的温度场以及变形体的应变场、应力场等不断发生变化。
-
This kind of brake squeezes the rims to slow and stop the bike.
这种制动的轮辋挤压缓慢，并停止自行车。
-
The development of Guangzhou privately operated shipping industry, especially for the shipping industry of inland rivers, had broken through the extrusion of foreign shipping industry, demonstrating strong vitalities, and actually became the main body and the backbone of national shipping industry.
广州民营航运业的发展，尤其是内河轮运业的发展，冲破了外国轮运业的挤压，显示了顽强的生命力，实际成为民族航运业的主体与中坚。
-
The barge pressed against the shell plating of the said ship, thus, the damage was sustained.
挤压 pressed 如：该驳挤压该轮船壳造成损坏。
- 更多网络解释与挤压轮相关的网络解释 [注：此内容来源于网络，仅供参考]
-
castanet：软件
铸挤压辅助药剂 cast, extrude , or pressed booster | Castanet 软件 Castanet | 脚轮 caster
-
castanet：软体
"铸挤压辅助药剂","cast, extrude , or pressed booster" | "Castanet 软体","Castanet" | "脚轮","caster"
-
Castanet Castanet：软件
铸挤压辅助药剂 cast, extrude , or pressed booster | Castanet Castanet 软件 | 脚轮 caster
-
squeezability：可压实性 可压缩性
squeegeeroller挤压轮 | squeezability可压实性 可压缩性 | squeezablewave-guide可压缩波导
-
squeezable wave-guide：可压缩波导
squeegee roller 挤压轮 | squeezable wave-guide 可压缩波导 | squeezable waveguide 可压缩波导管
-
pressive gradient：压力梯度
press wheel 镇压轮 | pressive gradient 压力梯度 | pressurant gas 挤压气体
-
squeegee roller：挤压轮
squeegee pump ==> 挤压泵 | squeegee roller ==> 挤压轮 | squeezable wave-guide ==> 可压缩波导