- 更多网络例句与截面模量相关的网络例句 [注：此内容来源于网络，仅供参考]
-
To measure diluting blood cell velocity with the Doppler anemometry with optical fiber in two dimensions, this can be observed the velocity situation in two dimensions of erythrocyte on certain scarf on vessel.
而采用二维方式设计光纤光源的都卜勒流速计模组量测稀释血液流速，可了解在血管某截面上红血球二维的流速情形，所得到的实验结果，可作为发展小型面积化雷射都卜勒模组的基础。
-
If we give some restrician to the intrinsic quantities of submanifolds, such as second fundamental form, scalar curvature,Ricci curvature or sectional curvature,then we can get some new property of the submanifolds.The procedure is called pinching problem of submanifolds.
对子流形的第二基本形式模长平方s，数量曲率R，Ricci曲率R_及截面曲率R_等内在量，加以某种限制，从而得到子流形的某些性质，叫做子流形的pinching问题。
-
According to two hypotheses: one for the relation between the dynamic complex stiffness and the material dynamic characteristics, another for the relation between the static displacement and the force acting on the element, the predicting formula for rectangular cross section are obtained respectively using the static stiffness formulation from the beam——column theory and the G〓bel method.
利用粘弹性材料的标准导数和分数导数模型的本构关系，建立了动态储能和损耗模量函数的关系式，由材料特性实验确定其中的参数，按元件的动态复刚度和材料动态特性之间与元件静态位移与作用力之间的关系假定，依柱梁理论或G〓bel的方法建立的静刚度表达式，建立了矩形截面环元件的刚度和阻尼的预测公式。
-
The flexural strength of this spicule is 394.34GPa, the flexural modulus increases with the growth direction of rounds.
这种骨针的弯曲强度为394.34GPa，弯曲模量随生长环带由中心向外逐渐增大；截面硬度为2.933GPa，截面杨氏模量为33.308GPa。
-
On the basis of detail analyzing the cause and influence factors of the approach slap design, this paper which utilize the flexible ground beam theory and finite element numerical calculation method to calculate the ground reaction、internal force and bending deflection, in each condition of disjoint and undisjoint of the approach slap near the abutment end, with the different ground module and length of the approach slap, achieves some valuable conclusions.
本文在对桥头跳车成因和桥头搭板设计影响因素作了详细的分析基础上，运用弹性地基梁理论和有限元数值计算方法，对桥头搭板在近台端不脱空和脱空时，在不同的地基模量及不同的搭板长度，搭板任意截面的地基反力、内力及挠度大小进行计算，得出了一些有意义的结论。
-
By simplifying the mechanical model,constitutive relation defined in principal direction based on elasticity theory with different moduli was rebuilt in common ordinates,and tension-compression area was divided.
通过合理简化模型，将不同模量弹性理论中定义在主坐标系下的本构关系重新建立在普通坐标系下，进行拉压分区，从而推导了考虑自重且顶部有水平推力的不同模量弯压柱近似弹性力学解答，并由横截面上正应力为零判定了中性层的形状和位置。
-
Second, the section modulus of the stem can be changed in seeral ways to allow greater flexibility while leaing the implant diameter unchanged so that stability is not compromised.
其次，有多种方法可改变柄的截面模量，以在不改变假体直径的基础上增加其柔韧性，并且保持其稳定性。
-
The formation of the dimple morphology is due to volume increased and transverse area unchanged during tensile process of PEEK.
韧窝的形成是由于聚醚醚酮具有高模量并在拉伸过程中未出现细颈化，而是在横截面积不变的情况下，发生了体积增大的现象。
- 更多网络解释与截面模量相关的网络解释 [注：此内容来源于网络，仅供参考]
-
section modulus：截面模量
section construction 组合式建筑 | section modulus 截面模量 | section paper 方格纸
-
relative viscosity：相对粘度(代号)
21.radius of circle of least confusion 圆周的最小模糊半径(代号) | 22.relative viscosity 相对粘度(代号) | 23.section modulus 断面模量,截面模量(代号)
-
plastic section modulus：塑性截面模量
塑性铰||plastic hinge | 塑性截面模量||plastic section modulus | 塑性理论||theory of plasticity
-
elastic section modulus：弹性截面模量
弹性极限||elastic limit | 弹性截面模量||elastic section modulus | 弹性理论||theory of elasticity