- 更多网络例句与废品率相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Results The lot tolerance percent defective, retest possibility, average sample number and disputable zone in ChP, ICH method and the advanced ICH method are 9.4%, 27.4%, 15.5 and 15.0%;5.5%, 69.6%, 23.9 and 11.0%;5.5%, 40.5%, 18.1 and 11.0%, respectively.
结果 《中华人民共和国药典》含量均匀度检查方法、ICH方法及ICH改进方法的批允许废品率、复试率、平均样本容量和争议区分别为9.4%、27.4%、15.5和15.0%；5.5%、69.6%、23.9和11.0%；5.5%、40.5%、18.1和11.0%。
-
Since there is no needto power off the machine during the process of measuring, it can reduce the workforce,heighten the production efficiency, depress the waster rate, and better the productcoherence. This kind of system is very suitable for the product pipelining which needshuge batches, such as auto components, axletree parts and so on.
由于它能使操作人员无需停机就能测量工件，减少了劳动强度，提高了生产效率，又降低了废品率，同时加工出的工件尺寸一致性较好，特别适应于在大批量流水线作业中使用，如汽车零部件、轴承零件的加工等。
-
Broken-rollers and stepless blad type double facer adopts combined structure which effectively overcometraditional low heat efficeency because of concave heat box when work,which improve work speed and qualit,decrease wasted board,especially suitable for light weight board.
其中碎辊式无级压载双面机采用碎辊结构，有效克服传统压载，因加热箱工作时下凹，导致热板上表面传热效率差的缺点，避免了传统压辊不平衡对纸板的冲击，从而提高了生产速度和质量，降低了废品率，更加适合克重纸板生产。
-
Introduce and promote continuous improvement measures to reduce the defectiveness of products / components.
持续推动改进方法以降低产品/部件的废品率。
-
Formulary to workshop responsibility percent defective delibrate Wang Ruixian of school of finance and trade of 10 lasher city, huang Deyan reject is the does not accord with a standard product that discovers in product quality inspection.
对车间责任废品率公式的研讨十堰市财贸学校王瑞先，黄德艳废品是在产品质量检验中发现的不符合标准的制品。
-
Bull;Suggest improvements in order to lower certain reject rates.
提出有效的改进的建议以降低废品率。
-
And therefore it avoided the phenomena that makes waster ratio to be higher caused by overhigh or lower temperature.
文中讨论台达温度控控器在塑料加工生产过程中的具体应用，以保证在复杂生产环境中精确地控制原料生产温度，避免温度过高或者过低造成废品率高的现象。
-
The methods for the traditional industrials marking are not only inefficient and unaesthetic,but also short of long term stability and high for the rate of waster .
传统的工业标记打印效率低、不美观、稳定性差、废品率高。
-
Longer Availability work time and lower wastrel rate, reduce the overall cost.
使停机次数和生产辅助时间减少，废品率下降，综合经济效益大大提高。
-
Quantitative analysis can be divided into 50－350g/m2, with no degradation of thin-film, anti-false, easy to use design-pattern, the paper surface gloss over foil, aucilisty, ployster polychloride membrane mirror paper, cards and membership cards make good adaptability, coating and pictorial proof alkali resistance, high alcohol being polished, scrap rate and business card printing and membership card making difficult well below the foil and polished to a mirror of paper.
定量可分为50－350g/m2，无薄膜、易降解、防伪图案采用隐含式设计，该纸表面光泽度超过铝箔纸、pET、聚酯聚铝膜镜面纸、制卡和会员卡制作适应性好，涂层和图案耐酸碱、耐汽油、耐酒精擦拭，废品率和制卡和会员卡制作难度大大低于铝箔纸和镜面纸。
- 更多网络解释与废品率相关的网络解释 [注：此内容来源于网络，仅供参考]
-
lot tolerance fraction defective：批容许废品率
lot 一批 | lot tolerance fraction defective 批容许废品率 | low of cosines 余弦定律
-
low of cosines：余弦定律
lot tolerance fraction defective 批容许废品率 | low of cosines 余弦定律 | lower approximate limit 下近似极限
-
rationalization scheme：合理计画
废品率 rate of rejects | 合理计画 rationalization scheme | 打磨滚筒 rattler
-
Scrappage：废品率、废料量
scrap material废料(废钢、废铁) | scrappage废品率、废料量 | scrapping报废
-
condemning limit：报废(尺寸)界限, 废品率
condemned | 被责难的, 被宣告有罪的 | condemning limit | 报废(尺寸)界限, 废品率 | condensability | 可压缩性, 可简约性
-
spongy manufactures：海绵制品
stevedore 装卸货人;理货人;码头装卸工;搬运工 | spongy manufactures 海绵制品 | spoilage rate 废品率