- 更多网络例句与局部压力相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Conditions of the seepage and stress is a dynamic process, and also shows its interaction and interdependence. Owing to the closure of the fracture, the hydraulic gradient and the permeability pressure of the fracture turn large, and also promote the expansion of water cracks, and fissures connectivity increasing. The increase of the crack opening width will result in the increase of the infiltration capacity and seepage flow, and the reduction of seepage pressure. Because of the dynamic dependence of the fracture aperture, pressure and seepage, under certain conditions, changes in fracture aperture can lead to the formation of local water-passage, and the local emission of high pressure water, and thus promotes the formation of the sudden outgush disasters.
结果表明:洞室开挖完成后,在围岩渗流与应力耦合作用下,围岩中裂隙隙宽、裂隙中水压及其渗透流量的变化是一个动态过程,且相互作用与相互依赖;裂隙的闭合使得结构面水力梯度变大,作用在裂缝上的渗透压力增大,促进导水裂缝扩展,裂隙连通性增加;裂缝张开度增大,渗透能力增强,渗流量增大,其渗流压力相应降低;由于围岩中裂隙隙宽、压力和渗流量的动态依赖性,在一定条件下,裂隙隙宽的改变可导致局部水力通道的形成,高压水头从局部涌出,从而促进突水灾害的形成。
-
Depending on the temperature and partial pressure, air contains varying amounts of water vapor.
根据对温度和局部压力的空气含有不同数量的水蒸汽。
-
The variation of saturation enthalpies of both phases and of the gas density with local pressure is taken into account.
两相的饱和焓以及汽相的密度被处理为随局部压力变化。
-
First according to the hydraulic pressure elevator system diagram, use the machine design and hydraulic transmission knowledge calculates the diameter of the plunger, cylinder tube wall thickness as well as cylinder bottom thickness; second, through the examination confirmation to the obtained result to complete the work of cylinder design; Simultaneously has carried on the component choice and the computation; Through to the system calorific capacity computation the and the volume of cooling water while the fuel tank cools when needs to complete the hydraulic pressure elevator fuel tank design; Based on the system oil stream condition to calculated the tube internal pressure lose, the local pressure loss as well as the all of the pressure lose to carried on the system checking calculation; Finally through the consult correlation design handbook to calculation and examines the belt, the band pulley, the axis, as well as the key, has completed the hydraulic pressure elevator pumping station transmission system design.
首先根据液压电梯系统原理图,利用机械设计与液压传动等方面的知识计算出柱塞的直径、缸筒的壁厚以及缸底厚度,并对所得结果进行校核验证完成了工作油缸的设计;同时进行了元件的选择和计算;其次,通过系统发热量的计算和油箱冷却时需要的冷却水量的计算完成了液压电梯油箱的设计;依据系统油流状态计算出管内压力损失、局部压力损失以及总压力损失进行了系统的验算;最后通过查阅相关设计手册对带、带轮、轴、以及键进行设计计算和校核,完成了液压电梯的泵站传动系统的设计。
-
Firstaccording to the hydraulic pressure elevator system diagram, usethe machine design and hydraulic transmission knowledge calculatesthe diameter of the plunger, cylinder tube wall thickness as wellas cylinder bottom thickness; second, through the examinationconfirmation to the obtained result to complete the work ofcylinder design; Simultaneously has carried on the component choiceand the computation; Through to the system calorific capacitycomputation the and the volume of cooling water while the fuel tankcools when needs to complete the hydraulic pressure elevator fueltank design; Based on the system oil stream condition to calculatedthe tube internal pressure lose, the local pressure loss as well asthe all ofthe pressure lose to carried on the system checking calculation;Finally through the consult correlation design handbook tocalculation and examines the belt, the band pulley, the axis, aswell as the key, has completed the hydraulic pressure elevatorpumping station transmission system design.
首先根据液压电梯系统原理图,利用机械设计与液压传动等方面的知识计算出柱塞的直径、缸筒的壁厚以及缸底厚度,并对所得结果进行校核验证完成了工作油缸的设计;同时进行了元件的选择和计算;其次,通过系统发热量的计算和油箱冷却时需要的冷却水量的计算完成了液压电梯油箱的设计;依据系统油流状态计算出管内压力损失、局部压力损失以及总压力损失进行了系统的验算;最后通过查阅相关设计手册对带、带轮、轴、以及键进行设计计算和校核,完成了液压电梯的泵站传动系统的设计。
-
Moreover, the hydraulic pressure pumping station has used the Neutral high hydraulic pressure actuation design and the small work current capacity, reduces the hydraulic system along the regulation resistance loss and the local pressure loss, reduces the pipeline interior fat liquor hit.
另外,液压泵站采用了的中高压液压驱动设计和较小的工作流量,以减少液压系统的沿程阻力损失和局部压力损失,减少管路内部油液撞击。
-
Moreover, the hydraulic pressure pumping station hasused the Neutral high hydraulic pressure actuation design and thesmall work current capacity, reduces the hydraulic system along theregulation resistance loss and the local pressure loss, reduces thepipeline interior fat liquor hit.
另外,液压泵站采用了的中高压液压驱动设计和较小的工作流量,以减少液压系统的沿程阻力损失和局部压力损失,减少管路内部油液撞击。
-
The model showed that a partial pressure of only 2.9 millibars of CO2 would have been needed during the late Archaean and early Proterozoic periods in order to bring the surface temperature of the Earth above freezing.
模拟显示:在太古代末期和原生代初期,要想使地球表面温度升高到凝点以上,只需要二氧化碳的局部压力达到2.9毫巴。
-
Millibars of CO2 would have been needed during the late Archaean and early Proterozoic periods in order to bring the su rface temperature of the Earth above freezing.
模拟显示:在太古代末期和原生代初期,要想使地球表面温度升高到凝点以上,只需要二氧化碳的局部压力达到2。 9毫巴。
-
The issue analyses and calculates the linear pressure loss and local pressure loss in spot example in the process as well as gets a conclusion.When several compressors in serial connection provide compressed air,the more the compressors be connected,the more the pressure loss to be happened,and gives a few of methods to reduce the pressure loss.
以实例详细计算了压缩空气在输送过程中的沿程压力损失和局部压力损失,并得出了结论:当多台空压机串联供气时,串联供气的空压机的台数越多,其串联在后面的空压机输出的局部压力损失就越大,并给出了克服压力损失的几种方法。
- 更多网络解释与局部压力相关的网络解释 [注:此内容来源于网络,仅供参考]
-
compressive force:压力
皱褶的发生系由於过大的压力(Compressive Force)造成之Wrinking现象或是多余的材料无法消化而起皱. 在实际的设计过程中,计算压力而去预测是否会发生皱褶,是一件极困难的是. 在加工过程中的流动方向,进而推断是否有局部多余的材料.
-
cooling:冷却
8.冷却(COOLING) 加入或混合气(5%max.) 处理压力850mbar 冷却至室温(60℃以下)制气体氮化简单易做可整体处理(混载)氮化层选择不易白层有微细孔洞,不致密有排放气体消耗大局部氮化困难不能氮化不锈钢及钛合金盐浴氮化氮化速度快处理均匀氮化层选择不易白层疏松、不致密局部氮化不易工作须缚紧,
-
erosion:浸蚀
又称浸蚀(Erosion).(Cavitation Erosion) 固体相对于液体运动时,由于液体中气泡在固体表面附近破裂时产生局部高冲击压力或局部高温引起的磨损. 又称气蚀(Cavitation)
-
coefficient of partial expansiveness:局部的扩充性系数,局部的扩充性系数
coefficient of partial determination 偏测定系数 | coefficient of partial expansiveness 局部的扩充性系数,局部的扩充性系数 | coefficient of passive earth pressure 被动土压力系数
-
gloss:光泽度
实验结果发现表面光差现象是因为局部剪应力变化造成表面塑料分子排列方向规则一致,使表面局部光泽度(gloss)提高所造成. 实验结果也显示,降低模温、减小气体压力、加快冷却速度、采用不定型分子材料及产品厚度设计避免剧烈改变,
-
ischemic penumbra:半暗带
近年来,许多动物实验及临床病理研究证实:在脑出血病灶周围的脑组织存在进行性水肿和缺血损伤"半暗带"(ischemic penumbra),其病理生理机制是局部脑组织压力升高、脑血流量(CBF)减少、BBB破坏与局部渗透性活性物质产生(结果引起血浆蛋白等的
-
spalling:剥落
(18)剥落(Spalling) 疲劳磨损时从摩擦表面以鳞片形式分离出磨屑的磨损. (CavitationErosion) 固体相对于液体运动时,由于液体中气泡在固体表面附近破裂时产生局部高冲击压力或局部高温引起的磨损.
-
locos:硅的局部氧化
在一个实例中,具有暴露的硅区的压敏电阻压力传感器经受了硅的局部氧化(LOCOS)处理. 用LOCOS工艺产生了电绝缘结构. 该绝缘结构与压敏电阻压力传感器具有圆形的或弯曲的界面. 该弯曲的界面减轻了伴随着暴露到高温和高压下的应力.
-
partial radiation pyrometer:部分辐射温度计
partial pressure 局部压力 | partial radiation pyrometer 部分辐射温度计 | partial refuelling 局部换料枷偿还
-
secondary rock pressure:二次岩石压力
secondary reduction 二次破碎 | secondary rock pressure 二次岩石压力 | secondary ventilation 局部通风