- 更多网络例句与实际强度相关的网络例句 [注：此内容来源于网络，仅供参考]
-
In accordance with the error function between the measured intensity and calculated intensity, and the regularization terms for different source models, this method estimates the illuminant direction for images of different source models.
该方法根据图像的实际强度与计算强度间的误差函数以及适合不同光源模式的约束条件，估计不同光源模式下图像的光照方向。
-
This paper presents classification of car steel sheet in Cherry Car Co.and introduction and description of practical propery tests,applications of super deep draw steel IF- cold rolled high strength sheet,bake hardening sheet- cold rolled dual phase steel sheet,TRIP sheet,Sandwich steel sheet and pickled oil steel sheet.
介绍了奇瑞公司轿车用超深冲IF钢板、冷轧高强度钢板、烘烤硬化钢板、冷轧双相钢板、相变诱导塑性钢板、减振复合钢板和热轧酸洗钢板的实际性能试验及应用，分析了国内外部分钢种的实际成分和性能以及用高强度钢板制造车身的减振效果，并对薄钢板和典型表面件的抗凹刚度和抗凹深度进行了检测。
-
The shearing failure of structural plane is considered to be corresponding to the maximum of real contact area, a criterion is given to distinguish the shearing failure of structural plane and a new select method of shear strength is brought forward subsequently; Examine the influence of geometrical features and thickness of weak intercalation on the integrative strength of weak structural plane based on the composing of basic strengths, formative mechanism of shearing plane and failure pattern; and present the quantitative relation between the strength and thickness.
4详细研究了依附型滑动面中的硬性结构面和软弱结构面力学特性和破坏模式，对硬性结构面引入摩擦学中的粘着摩擦理论，着重研究结构面在剪切过程中实际接触面的变化规律，提出实际接触面积的最大点即为强度破坏点，并结合实际数据进行了验证；对软弱结构面则从其基本强度的组成、内部剪切面的形成机理和破坏模式入手，研究了结构面的几何特性、夹层厚度和强度关系对软弱结构面综合强度值的影响，并给出了定量关系式。
-
The main reason why quarter-sawn board of Birch had smaller dry compressing shear strength than flat-sawn board of Birch in normal conditions was that Birch had different shear strength to the grain between quarter-sawn board and flat-sawn board. Meanwhile xylary rays in flat-sawn board were transversely cut and left a lot of pores in the flat-sawn board, so adhesive can enter these pores and turn into adhesive nail. While these pores provided a kind of tunnel for water, so cause this phenomenon that wet compressing shear strength of flat-sawn board of Birch was smaller than that of quarter-sawn board of Birch. The possible reason why quarter-sawn board of Oak had greater dry compressing shear strength than flat-sawn board of Oak in normal conditions was that ratio of springwood on quarter-sawn board and flat-sawn board was different.
造成柞木径切板的常态压缩剪切强度比弦切板的常态压缩剪切强度大的主要原因是，在径切板和弦切板上早材胶接的比例不同，径切板的胶合强度试件上早材胶接的比例相对少，而弦切板的胶合强度试件上早材胶接的比例比径切板的胶合强度试件上早材胶接的比例相对大，由于早晚材胶接过程中强度决定于早材，这部分胶接强度比较低，这就使得柞木径切板的常态压缩剪切强度比弦切板的大；同时在柞木弦径面胶接过程中由于实际胶接面积的不同也能造成弦径面上API胶粘剂与之形成的化学键的数量不同，这也是造成柞木径切板的常态压缩剪切强度比弦切板的大的原因之一。
-
The calculating results are compared with the test data in available literatures and FEM results. The research results show that the plastic hinge model is precise and correct, which can satisfy with the actual engineering demands. The collapse pressure of perforated liner casing decreases with phrase angle, initial ovalization and diameter-thickness ratio increasing, and increases with the yield stress. The phrase angle and initial ovalization have greatly influence on the collapse pressure. The collapse pressure of perforated liner casing is slightly changed with the diameter and density of perforation when the diameter and density are smaller than 12mm and 120 shots per meter, respectively.
计算结果表明：筛管抗挤强度的塑性铰模型具有很高的计算精度和准确度，可以满足工程实际需要；筛管抗挤强度随着射孔相位角、径厚比和初始椭圆度的增加而降低，随着屈服强度的增加而增加，相位角和椭圆度对筛管抗挤强度影响比较显著；在射孔直径小于12 mm、射孔密度小于120 孔/ m 时，筛管抗挤强度随射孔直径和射孔密度增加变化不明显。
-
Overstrength factors of reinforced concrete frames are studied under different design parameters based on seismic design code.
结合我国建筑抗震设计规范，研究不同设计条件下R.C框架结构的超强系数，然后乘以设计地震作用确定结构的实际强度。
-
In this work the unhomogeneity of microstructure in product strips has been studied, and the methods to control grain size with the hot rolling technological parameters are given. The capacity to control the property unhomogeneity of hot strips has been greatly improved after using the methods. According the statistics of production, the the property unhomogeneity over 99% strips is less than 80 MPa in a batch of coils, and less than 40MPa in a coil.
8对大量实际生产带钢组织和性能的不均匀性进行了研究，提出了通过调整热轧工艺参数来进行晶粒尺寸均匀度控制的的具体措施，实际生产采取该控制手段后，使宝钢对管线钢性能波动的控制水平得到大幅度的提高；强度波动由管线钢生产初期的批量内150～200MPa，卷内100MPa提高到批量内00MPa，卷内0MPa，可按合同交货；大生产实际水平为：99％产品的强度波动量达到批量内0MPa，卷内0MPa。
-
The influence of recessing in adh es ive layer with high elastic modulus on the peak stress of joint is not evident so that it would improve the actual strength of joint markedly based on the load bearing ability not being affected evidenly . On the other hand , the recessing in the joint with low elastic modulus adh es ive caus es the peak stress es increase evidently that may decrease the nominal and actual strength of the joint markedly .
对胶层和被粘物中应力分布的数值分析结果表明：胶层中的间隙对接头端部的应力分布无明显影响，但对间隙附近的应力峰值影响较大；随着胶粘剂弹性模量的增大，间隙附近的应力峰值有所降低；对于高弹性模量胶粘剂接头，胶层中的间隙对接头的应力峰值无明显影响，在不降低接头名义强度的同时可使得接头的实际强度显著提高；而对于低弹性模量胶粘剂接头，间隙使得接头上的应力峰值明显上升，可能导致接头的名义强度和实际强度显著降低。
-
After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.
3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。
-
Introduce the cohesion-friction model of rock strength theory, and extend the model to select the strength of sliding plane, discuss the variation rules of peak strength and residual strength under different normal stress, and then present the selection model of shearing strength. After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.
3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。
- 更多网络解释与实际强度相关的网络解释 [注：此内容来源于网络，仅供参考]
-
in abeyance：归属待定
improper works 不合格工程 | in abeyance 归属待定 | in situ actual strength of concrete 现场混凝土实际强度
-
acclimation：适应
这部分工作将回答下列问题:理解高寒 针叶林建群种生理和生态过程对升高 二氧化碳和温度的响应机理并对 生理过程适应 (acclimation)参数值做出估计. 拟解决的 关键技术是如何定量其它限制源(如养分、植物库强度等)对实际参数值的干扰;
-
actual flux density：有效磁感应[强度],实际磁通密度;有效通量密度
actual flow of heat-supply network 热网实际流量 | actual flux density 有效磁感应[强度],实际磁通密度;有效通量密度 | actual gap area 磁极下气隙计算面积,实际气隙面积
-
Actual Laundering：实际水洗
SEAM SLIPPAGE接缝滑裂 | ACTUAL LAUNDERING实际水洗 | SEAM STRENGTH接缝强度
-
white noise：白噪音
"白噪音"(White Noise)是指:在宽频带内幅度(强度)均为随机的一类声波. 在实际应用中,"白噪音"经常被用来测试音箱的谐振和灵敏度. 近年来,一些人经常会接收到一些神秘的白噪音,在这些白噪音中会夹杂着一些特殊的声音,
-
Organon：研究法
1810年,赫尼曼医师发表了研究法(Organon)一书,书中内容主要是利用实际例子与理论来详细说明顺势疗法. 而这本书总共发行了六版,最后一版是在1842年发行,他在书中说明了他的最新发现LM-或Q-药力强度. 1811年,
-
osmotic potential：渗透势
渗透作用的强度可用渗透势(osmotic potential)来表示,渗透势实际就是溶液的水势与纯水水势之差,即渗透势=水势溶液-水势纯水内吞作用又称胞吞作用,就是由于质膜下微丝收缩,造成质膜向内折入,将胞外的固体颗粒或液体包入,
-
pixel：象素
发光二极管的亮度一般用发光强度(Luminous Intensity)表示,单位是坎德拉cd;3) 象素(Pixel)与象素直径>--LED电子显示屏常用术语(下) 6) LED显示屏(LED Panel) 将LED象素模块按照实际需要大小拼装排列成矩阵,