- 更多网络例句与夹销相关的网络例句 [注:此内容来源于网络,仅供参考]
-
This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.
此次设计是对拨叉零件的加工工艺和夹具设计,其零件为锻件,具有体积小,零件复杂的特点,由于面比孔易加工,在制定工艺规程时,就先加工面,再以面为基准来加工其它,其中各工序夹具都采用专用夹具,特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中,选一面两销的定位方式,并以操作简单的手动夹紧方式夹紧,其机构设计简单,方便且能满足要求。
-
This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.
此次设计是对拨叉零件的加工工艺和夹具设计,其零件为锻件,具有体积小,零件复杂的特点,由于面比孔易加工,在制定工艺规程时,就先加工面,再以面为基准来加工其它,其中各工序夹具都采用专用夹具,特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中,选一面两销的定位方式,并以操作简单的手动夹紧方式夹紧,其机构设计简单,方便且能满足要求。关键词拨叉,加工工艺,专用夹具,设计
-
According the practical machining requirement,we designed a new cartridge clip cemented carbide boring cutter based on boring rod slice slot,nut cartridge clip and circular pin orientation....
根据实际生产需要,运用刀杆开槽、螺母弹夹、圆销定位等原理设计出弹夹式微型机夹硬质合金精镗刀,很好的解决了小深孔零件的精密镗削加工。
-
We provide you with a variety of coupling: a patch-coupling, 2 drum gear coupling, three teeth coupling, 4-pin set of flexible couplings, 5-swelling connection kit, 6 Snake Spring couplings, coupling flanges 7, 8 radial button rigid couplings, coupling shell folder 9, 10-pin flexible couplings, 11-pin flexibility of the tooth - Axis, the Plum Blossom 12-coupling, 13 tire coupling, 14 Cross Coaxial universal joint, slider coupling 15, 16 roller chain coupling, and other non-standard coupling and inverse Only, Clutch, and other transmission equipment.
我们为您提供的联轴器品种有: 1 膜片联轴器、2 鼓形齿联轴器、3 齿式联轴器、4 弹性套柱销联轴器、5 胀紧联接套、 6 蛇形弹簧联轴器、7 凸缘联轴器、8 径向键刚性联轴器、9 夹壳联轴器、 10 弹性柱销联轴器、11 弹性柱销齿式联轴器、12 梅花型联轴器、13 轮胎式联轴器、 14 十字轴式万向联轴器、 15 滑块联轴器、16 滚子链联轴器等其它非标联轴器和逆止器、超越离合器等传动设备。
-
The tapered cottar, sells the axis, the insulating clamp, the clamp, the card hat, the copper fastener, the hot-water heat fitting, the fastener half-finished product, the fastener generation of purchase production and the service.
圆锥销、销轴,线夹,卡帽,铜紧固件,水暖配件,紧固件半成品,紧固件代采购的生产及服务。
-
This design takes the diesel cyclinder tank for the clamping and locating device of tank boring and designing the clamping regulations of arts and crafts of tank, we take two cylinders and one face to locate which can limit six free dgrees In order to reduce errors of tank during processing,we take standard and concurrent principle,unify principle,principle with each other for basis and selection of rough basis into order to make the orientation tight enough,it is required to insist in the principle of using the unrepeated coarse beach mark as possible as you can.
本设计以柴油机汽缸箱体为例,对箱体镗孔的夹紧和定位装置进行工艺分析和夹具的设计。在对此箱体的工艺规程采用两销一面对其进行定位以限制其六个自由度。为减少箱体在加工过程中的误差,我们考虑基准的重合原则,统一原则,互为基准原则以及粗基准的选择原则,为使定位稳定夹紧可靠,要求所选用的粗基准尽可能不重复使用原则。
-
A camming section (88) formed on an interior wall of sleeve (78) is captured between a head (124) of a pin (122) and a detent ring (132) to latch sleeve (78) in an unclamped mode.
制在套(78)内壁上的凸轮控制部分(88)锁位在销(122)的头部(124)与锁圈(132)之间以在非夹紧状态下锁住套(78)。
-
The gear mentions and the position of intermediate propeller shaft is decided by the means " computation, mapping and tries to collect many times". Calculates the coordinates of the spindle and drive shaft and checking the center distance, determined department spindle must use dislodges the gear.
本课题设计的组合机床采用&一面两销&定位、液动夹紧,一次装夹加工柴油机齿轮室盖三个面上的孔,保证了加工精度,提高了生产效率,减少了工人的劳动强度。
-
According to work piece size, characteristic and its material choice cutting specifications; Because of the thick mill diesel engine cylinder body two sides, then the jig design use "two sells the localization at the same time", Manual clamps, an attire clamps processes the diesel engine to be mad the cylinder body two sides; according to will work receives the cutting force to calculate clamps the strength; again according to clamps the strength , choose the determination clamp the special-purpose part.
由于是粗铣柴油机气缸体两侧面,则夹具的设计采用&一面两销&定位,手动夹紧,一次装夹加工柴油机气缸体的两个侧面,保证了加工精度,提高了生产效率;根据工作将受到切削力来计算夹紧力;再根据夹紧力来选择确定夹紧装置的专用部件。
-
The impoved design of the D35 trailor-form is rational, since the wagon ear is connected with the heavy load by hingel joint instead of spherical articulate, and the lateral relative displacement of safety pins is very small due to the rolling stiffness of schnabel grider, so that the friction stability of spherical-surface sockets of press-down cylinders is guaranteed.
新型D35联挂改进设计是合理的,因为车耳球铰改为车耳铰销联结后,利用钳夹梁的侧扭刚度来减小安全销相对横向位移,进而保障压柱油缸球面座的摩擦稳定性。
- 更多网络解释与夹销相关的网络解释 [注:此内容来源于网络,仅供参考]
-
clevis pin:牵引钩联结销,马蹄钳栓
clevis joint 拖钩,脚架接头 | clevis pin 牵引钩联结销,马蹄钳栓 | clevis u 形夹
-
dowel pin:定位销
单击"定位销 定位销"(Dowel Pin) > "...装配自动螺钉 装配自动螺钉"(...assemble Autoscrews).选择底部夹持板装配新销钉. 定位销 装配自动螺钉 要重定义预定义的定位销设置,请在零件模式下再次单击"定位销 > "...预定义 定位销" 预定义".EMX 将识别这些参数,
-
spring pinchcock:弹簧节流夹
spring pin 弹簧销,弹性销 | spring pinchcock 弹簧节流夹 | spring piot 钢板弹簧销
-
tool post:夹刀柱
倒头销 toggle pin | 夹刀柱 tool post | 长顶游艇 top open yacht
-
SNAP PINS:格式管夹、管束 R型销
销 PINS | 格式管夹、管束 R型销 SNAP PINS | 闸、锁 LATCHES AND KEEPER ASSEMBLEDS
-
cinder pig iron:夹渣生铁
core pin 中心销, 塑孔栓 | cinder pig iron 夹渣生铁 | isopentenylpyrophosphate 异戊烯焦磷酸
-
dog chart:销簧
dog catch ==> 卡子,擒纵器 | dog chart ==> 销簧=>ドッグチャート | dog chuck ==> 爪形夹盘
-
clevis pin u:形夹销
adapter转接器 | clevis pin u形夹销 | nitrogen load.dev.负载氮气
-
steering lock pin:转向锁销
steering lock clamp;转向锁夹 | steering lock pin;转向锁销 | steering malfunction;转向失灵[故障]
-
auxiliary spring nut pin:副簧螺母销
auxiliary spring clamp ==> 辅助弹簧夹 | auxiliary spring nut pin ==> 副簧螺母销 | auxiliary spring plate ==> 辅助弹簧垫片