填料函压盖

词组短语

junk ring

与填料函压盖相关的网络例句 [注：此内容来源于网络，仅供参考]

Valve:(dark-parallel) 1 - wedge-shaped gate valve; 2 - sleeve nut; 3 - Valve; 4 - stem; 5 - valve cover; 6 - Thrust Convex shoulder; 7 - Packing letter flange; 8 - packing; 9 - Packing Gland, 10 - hand wheel; 11 - valve cover pad.

闸阀：1--楔形闸瓣；2--套筒螺母；3--阀体；4--阀杆；5--阀盖；6--止推凸肩；7--填料函法兰；8--填料；9—填料压盖；10--手轮；11--阀盖垫。

Clean and check 1 slowly loosen the gland nut stuffing, packing the release of residual pressure of all components; 2 Remove all old packing, thoroughly clean axle / rod stuffing; 3 Check the shaft / bar have corrosion, dents, scratches or excessive wear; 4 Check whether there are other WATER POWER CONTROL VALVE parts burr, cracks, wear, they will reduce the packing life; 5 Check whether there is too much stuffing the gap, and the shaft / rod eccentric degree; 6 the replacement of defective parts larger; 7 Check the old packing, as BALANCING VALVES the basis of failure analysis to find the reasons for early failure of packing.

缓慢松开填料函的压盖螺母，释放盘根组件内所有的残余压力； 2）移去所有旧的盘根，彻底清洁轴/杆的填料函； 3）检查轴/杆是否有腐蚀、凹痕、划伤或过度磨损； 4）检查其他零件是否有毛刺、裂纹、磨损，它们会减少盘根的寿命； 5）检查填料函是否有过大的间隙，以及轴/杆的偏心程度； 6）更换有较大缺陷的零部件； 7）检查旧盘根，作为失效分析的依据，球阀以找到盘根早期失效的原因。

The basic form of stuffing:(1) gland-type This is the most used form.

填料函的基本形式是：(1)压盖式这是用得最多的形式。

Stuffing the basic form is:(1) gland-type This is the most used form.

填料函的基本形式是：(1)压盖式这是用得最多的形式。

Stuffing mainly by the packing, seal ring, filling cylinders, packing gland, water-sealed tube.

填料函主要由填料，水封环，填料筒，填料压盖，水封管组成。

Included in the complete filling of the following letter of component parts inside the part or all of the combination of: packing, packing gland, packing nuts, rings, packing spring, packing flange, packing flange stud or single-head bolt , packing flange nuts, packing ring, packing isolated loop, blankets isolation ring, BeIIev Sichuan e springs and anti-extrusion ring.

包括在完整的填料函组件里的是下列零部件的部分或全部的组合：填料、填料压盖、填料螺母、套环、填料弹簧、填料法兰、填料法兰双头螺栓或单头螺栓、填料法兰螺母、填料环、填料隔离圈环、毛毡隔离圈、BeIIev川e弹簧和抗挤压环。

与填料函压盖相关的网络解释 [注：此内容来源于网络，仅供参考]

stern-tube longshoreman：装卸工人

stern-tube bulkhead 尾轴管舱壁 | stern-tube longshoreman 装卸工人 | stern-tube packing gland 尾轴管填料函压盖

piston rod guide：海塞杆导承

piston rod gland 活塞杆填料函压盖 | piston rod guide 海塞杆导承 | piston rod guide 活塞杆导承

stuffing box bearing：填料压盖轴承

stuff grinder 磨浆机 | stuffing box bearing 填料压盖轴承 | stuffing box bushing 填料函衬套

stuffing box gland：填料函压盖

金属填料 metallic stuffing | 填料箱,填料函 packing box, stuffing box | 填料函压盖 stuffing box gland

stuffing box gland：填料涵压盖

stuffing box complement for piston rod 活塞杆填料函总成 | stuffing box gland 填料涵压盖 | stuffing box gland 填料函压盖

stuffing box cover：填料函压盖 填料箱压盖

quatrimycin 差向四环素, 四-霉素 | stuffing box cover 填料函压盖 填料箱压盖 | selective plating (微生物)选择性平皿培养(法) [冶]选择镀

glandless pump：无填料函泵

gland 压盖 | glandless pump 无填料函泵 | glands 气封

follower plate：随动板; 仿形圆盘; 填料函压盖

follower pile 送桩 | follower plate 随动板; 仿形圆盘; 填料函压盖 | follower pulley 从动皮带轮

Junk ring：填料函压盖

junk retriever 打捞碎物工具 | junk ring 填料函压盖 | junk shot 炸碎井下落鱼的炸药包

junk ring bolt：压环螺栓

juniorofficer 初级船员 | junk ring bolt 压环螺栓 | junk ring 填料函压盖承磨环