固化

基本解释 (translations)

curing  ·  solidifying

与固化相关的网络例句 [注：此内容来源于网络，仅供参考]

Cement and silver sand are used as the basis materials for solidifying galvanized sludge containing heavy metals such as Ni,Cr and Cu,the lixivium test to solidified matter shows that the effect of solidifying galvanized sludge with cement is good.

采用水泥和细砂作固化基材处理含Ni、Cr、Cu等重金属的电镀污泥，对固化块的浸出试验表明：水泥固化该电镀污泥效果良好，固化过程中加入适当的螯合剂KS-3，可以提高固化效果，并对固化块在不同pH浸取剂下的重金属浸出浓度进行了研究。

The mold is made of the silicone pattern layer with a quartz supporting plate. The parameters in a vacuum casting process and a hardening process for composing the silicone are optimized to improve the physical properties of the mold to keep adequate demold and pattern accuracy.

分析了硅橡胶模具制作工艺中真空辅助浇铸的成型过程，以及交联固化反应过程的各个工艺参数对硅橡胶模具性能的影响，通过大量实验，具体分析了硅橡胶单体和固化剂配比、浇铸真空压力、固化温度及固化时间等工艺参数，并由此得到了优化的硅橡胶固化工艺参数，提高了硅橡胶模具的物理性能。

The properties of TCC with ATS were as good as the TCC with HTS, better that the requirement of standard GB8744-88 for semi-graphitic carbon block. As good as TCC with HTS in industrial cells, the TCC with ATS also reduces the sodium penetration to cathodic lining, no tear-off of the coating was found after starting up of the cells. As compared with reference cells, the operation of coating cells with ATS was also improved to keep good shape of cell chamber, reduce the formation of sludge on the cell bottom, and gain more uniform current distribution. The ohmic drop of TCC cell bottom was lessened by 11. 5mV. The current efficiency was increased by about 1. 48% in average. It was estimated that the TCC life could be 44 months. Obviously, the TCC with ATS could also improve the performance of industrial cells, save energy, and increase the cell life.

对常温固化涂层槽的考核表明，与高温固化涂层槽一样，阴极内衬对钠的吸收减少，钠渗透速度减缓，从而减小钠膨胀危害，减少了铝电解槽早期破损的几率；启动后，常温固化涂层不脱落，同样具有良好的粘接性能；与对比槽相比较，常温固化涂层槽正常生产后，阴极表面干净、光洁，无沉淀或结壳，炉膛规整，阴极、阳极电流分布均匀，炉底压降降低（平均降低11.5mV），电流效率提高（平均提高1.48％）；涂层在电解槽内存在的时间可达到44个月以上；常温固化涂层同样可以起到改善电解槽工作状态、节能降耗、延长槽寿命的作用。

The formation of charge transfer complex was studied in the first part. The second part includes the synthesis and characterization of the acrylated unsaturated polyester and the kinetic studies on the Ar-UPE/ triethylene divinyl ether (DVE-3) photocuring system, the rheology and properties of film after photocuring. The third part includes the synthesis and characterization of the urethane modified unsaturated polyester and the kinetic studies on the PU-UPE/DVE-3 photocuring system, the rheology and properties of film after photocuring. The fourth part includes the synthesis and characterization of the vinyl ether end capped polyurethane and the kinetic studies on the VE-PU/DVE3 photocuring system, the rheology and properties of film after photocuring.

整个研究工作分为四个部分：一是电荷转移复合物的研究；二是丙烯酰氧基化不饱和聚酯的合成，表征，Ar-UPE/二缩乙二醇二乙烯基醚（DVE-3）体系光固化动力学研究以及Ar-UPE/DVE-3体系流变性能和光固化后涂膜综合性能的研究；三是氨酯改性的不饱和聚酯的合成，表征，PU-UPE/DVE-3体系光固化动力学研究以及该体系光固化后涂膜综合性能的研究；四是乙烯基醚封端的聚氨酯的合成，表征，VE-PU/马来酸二甲酯体系光固化动力学研究以及VE-PU/DMA体系流变性能和光固化后涂膜综合性能的研究。

The results show that Irgacure1000 is preferable in the system and the rate is highest when the amount of Irgacure1000 is 3%;the drying condition has a considerable impact on the rate ; it decreases with the increase in neutralization degree;when NaOH is used as neuralization agent,the rate at the later period is higher than that when triethyl amine used; the structure of polymer has a certain effect on the rate and it accelerates with the increase in the ratio of PBA/DMPA and HEAD/DMPA.

结果表明，本体系优选光引发剂Irgacure1000的质量分数为3%时固化速度最快；干燥条件对光固化速度有很大的影响；随着中和度的提高，固化速度下降；用NaOH作为中和剂时，后期固化速度快于用三乙胺；聚合物结构对固化速度有一定的影响，随着PBA/DMPA和HEA/DMPA比例的提高，固化速度加快。

Firstly, by using DSC, we analyzed the effect of the type and content of initiators on the curing reaction, Then, through FTIR, we discussed the final degree of cure of the cured resin and the performance of the cured resin by testing the static mechanical performance and DMTA, found that moderate content and ratio of the initiators system can cause the moderate cure temperature, increase of exotherm and the final degree of cure result from the cooperation effect of the two kinds of initiators, and found that the cooperated initiators system can effectively increase the final degree of cure even in low content.

通过差示扫描量热法分析了不同固化剂体系对树脂固化行为的影响，用红外光谱分析了不同固化剂体系下的浇铸体的固化度，并对树脂浇注体静态力学性能及动态机械热分析，认为不同活性的固化剂联用存在协同效应，使固化反应温度适中，固化反应更加充分，提高树脂固化度和扩大聚合物网络，使树脂浇注体拥有良好的力学性能和耐热性。

Two series of polyurethane acrylate grafted acrylic resins (Acr-g-TPU-PETA and Acr-gPPU-PETA) self-emulsifying systems are obtained by grafting -NCO group modified polyurethane acrylates with acrylic copolymer prepared from n-butyl acrylate, styrene,βhydroxyethyl methacrylate and acrylic acid The self-emulsifying systems showed Newtonian fluidity with viscosity closed to that of water, the solid contents were around 30% The T〓 of 15～4℃ for dried film before photocuring favored film formation at room temperature DSC and DMA results showed that PU-PETA is compatible with acrylic resin in the grafted resin The TG and dTG curves for Acr-g-PU-PETA samples were substantially different from the corresponding blends, and the brodened dTG peaks for photocured grafted resin suggest that there might be multiple interactions among chain segments The photocued film of the grafted resins self-emulsifying system exhibited good overall properties with polyurethane acrylate grafts ranging from 30% to 50%, and Acr-g-TPU-PETA series showed better properties than Acr-gPPU-PETA series The adhesion of the photocured film was 1～2 grade, impact strength was 50kg-cm and flexibility was 1mm The Shore hardness and the adhesion of the film decreased markedly if PETA was replaced by HEMA as photoactive group due to the lower C=C double bond content in the grafted resin The polyhydroxy amine-linked thioxanthones photoinitiators can be evenly dispersed in self-emulsifying system without color spot appearing in the dried film The films photocured with IV〓～IV〓 generally exhibited higher Shore hardness, gloss and solventresistance than that cured with Irgacure 2959 and did not induce the rusting of the iron substrate Pigmenting with titanium oxide had no effect on the photocuring The polyhydroxy amine-linked thioxanthone IV〓 and IV〓 can be new candidates for the formulation of titanium oxide pigmented photocurable water-borne coatings for their pale-yellow appearance and slight interference with the color of the coatings WB 4759 with high water-solubility coalesced and separated from the dried resin film, and even induced the rusting of iron substrate.

以丙烯酸丁酯，甲基丙烯酸-β-羟乙酯，丙烯酸及苯乙烯合成厂丙烯酸共聚树脂，并与含-NCO端基的聚氨酯丙烯酸酯接枝反应，经水性化后，得到两个系列（Acr-g-TPU-PETA和Acr-g-PPU-PETA）各5个不同配比的丙烯酸树脂接枝聚氨酯丙烯酸酯自乳化体系，粘度与水相近，为牛顿流体，固含量30％左右。光固化前干燥涂膜的玻璃化转变温度在-15℃～4℃之间，有利于室温下成膜。DSC及DMA谱表明两种树脂基本相容。Acr-g-PU-PETA的热失重行为明显不同于共混材料，接枝样dTG峰明显宽化，表明接枝样中链段之间的相互作刚有多重性，丙烯酸树脂与聚氨酯之间有一定的相容性。接枝树脂自乳化体系光固化涂层的综合性能以聚氨酯丙烯酸酯成分为50％～30％者相对较好，且以Acr-g-TPU-PETA系列更理想。光固化膜的附着力为1～2级，冲击强度为50kg·cm，柔软性多为1mm。以HEMA代替PETA作为接枝树脂的活性基团，碳—碳双键密度太低，光固化膜交联点太少，硬度和附着力均较差。多羟基胺连硫杂蒽酮光引发剂能均匀分散于树脂自乳化体系和接枝树脂干膜中，不出现色斑，光固化膜肖氏硬度一般高于以Irgacure 2959为光引发剂的光固化膜，光泽度及耐丁酮溶剂性能均有所提高，不会诱导铁基生锈，钛白着色对光固化结果几乎没有影响。本论文所合成的多羟基胺连硫杂蒽酮光引发剂IV〓与IV〓为浅黄色，对光固化涂层的颜色干扰较小，为配制钛白着色光固化水性涂料提供了新的光引发剂。水溶性太强的WB 4759在干膜中易聚结析出，且对所附着的铁基有诱导锈蚀作用。

Solidify time: usually the cloud stone glue could use proper solidify agent to increase or shorten the solidify time, but for stone hooking structure glue, it can not do in this way.

由于施工人员的云石胶使用习惯会造成干挂胶的使用误区，比如用固化剂来调节固化时间，云石胶可用固化剂量的适当增减来调节固化时间，有些施工人员就会沿用到干挂胶使用上，靠加大固化剂投量，以达到快速固化的目的。

This paper analyses and discussed solidification theories, status of solidification research and application, application field, advantage and disadvantage of cement solidification, bitumen solidification, plastic solidification, glass solidification and synroc solidification quite systematically.

对水泥固化、沥青固化、塑料固化、玻璃固化、人造岩石固化等5种固化处理方法的固化机理、研究现状、应用情况、适用领域及优缺点进行了较系统的分析探讨。

This paper analyses and discussed solidification theories, status of solidification research and application, application field, advantage and disadvantage of cement solidification, bitumen solidification, plastic solidification , glass solidification and synroc sol.

对水泥固化、沥青固化、塑料固化、玻璃固化、人造岩石固化等5种固化处理方法的固化机理、研究现状、应用情况、适用领域及优缺点进行了较系统的分析探讨。

与固化相关的网络解释 [注：此内容来源于网络，仅供参考]

curing agent：固化剂

固化剂 (Curing agent)是热固性树脂必不可少的固化反应助剂,对于环氧树脂来说本身品种较多,而固化剂的品种更多仅用环氧树脂和固化剂两种材料的不同品种相组合就能组成应用方式不同和性能各异的固化产物.

Catalyst pump：固化剂泵

Catalyst manifold|固化剂总成 | Catalyst pump|固化剂泵 | Catalyst ratio|固化剂比率

ultraviolet curable resin：紫外线固化树脂

ultraviolet curable resin coated fiber 紫外固化树脂涂覆光纤 | ultraviolet curable resin 紫外线固化树脂 | ultraviolet cured silicone acrylate 紫外光固化有机硅丙烯酸酯

curing time：固化时间

固化条件:完全固化的时间,依固化的温度而定,下列表中为基本固化时间:温度(Temperature) 固化时间(Curing Time)100℃-120℃ 50-70分钟

GUV：紫外光固化硅橡胶涂料

(GUV)行业下游发展状况分析三、紫外光固化硅橡胶涂料(GUV)行业下游对紫外光固化硅橡胶涂料(GUV)行业影响力分析第十二章 紫外光固化硅橡胶涂料(GUV)重点企业发展分析第十三章 紫外光固化硅橡胶涂料(GUV)行业投资策略分析第

immobilize waste：固化廢料

固化 immobilize | 固化废料 immobilize waste | 固化废料 immobilized waste

solidification point：固化点

solidification heat 固化热 | solidification point 固化点 | solidifying 固化

solidifying：固化

solidification point 固化点 | solidifying 固化 | solidifying point 固化点

cured：固化的

cure固化 | cured固化的 | curing固化

LCM：液态固化剂

年华南地区液态固化剂(LCM)行业分析第五节 2009年华中地区液态固化剂(LCM)行业分析第六节 2009年西南地区液态固化剂(LCM)行业分析第七节 2009年西北地区液态固化剂(LCM)行业分析第五章 液态固化剂(LCM)行业投资与发展前景