- 更多网络例句与变形椭圆相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Employing the bidimensional regression along with standard deviational ellipse, the authors compared the local and global distortions between two kinds of cognitive maps.
在此基础上，通过二维回归与误差椭圆的方法分别对两种外部化方法获得的结果进行全局与局部的比较，研究发现手绘草图的方法的结果更加符合实际地图；然而两个方法在变形的趋势上却大致相同。
-
The numerical analysis method is used to study the ground movement laws caused by the ovalization variation in the cross section in the action of water and soil pressure of tunnel lining.Based on the stochastic medium theory,this paper suggests the method for calculating this ground movement caused by tunnel ovalization deformation.
采用数值分析方法研究了隧道衬砌在土水压力的作用下，断面所产生的椭圆化变形引起的地层位移规律，并基于随机介质理论，给出了计算隧道椭圆化变形引起地层位移的方法。
-
The spatial geometry parameters of the deformation ellipse can be calculated through accurate spatial ellipse fitting.
通过高精度的空间椭圆拟合可以解算出变形椭圆的空间几何参数。
-
Based on theoretical study and test, by using finite element numerical method, the force and deformation of casing with cement sheath under nonuniform load is analyzed, and the effect of two sensentive parameters, the nonuniform load ratio and ellipticity, on the failure of casing is discussed.
在已有的理论研究与试验工作的基础上，采用有限元数值方法，分析计算了受非均匀地应力作用下套管-水泥环结构的受力与变形，讨论了两个敏感参数——非均匀载荷比和套管椭圆度对套管失效的影响问题。
-
The influence of expanding-die diameter on the quality of finished products, such as the uniformity of deformation, the contour of a cross section and its ellipticity as well as the wall thickness of finished products, is discussed specially; a conception of relative radius of punch and the design criterion of it are given in this paper.
本文专门论述了机械扩径模具直径对成形品质的影响，提出了相对凸模半径的概念，系统分析了它对变形分布、成形件轮廓形状、椭圆度和壁厚的影响。
-
Then the single layer spherical, cylindrical, elliptic paraboloidal reticulated shell and double layer cylindrical reticulated shell are calculated on the large deformation stability respectively, which show the application of the development system on the large deformation stability analysis of space bar structures.
用所开发的系统对单层球面网壳、圆柱面网壳和椭圆抛物面网壳以及双层柱面网壳进行了大变形稳定性计算，说明了所开发系统的可应用性。
-
The PZT plates were polarized in thickness direction. By using the deformation in the plane perpendicular to the direction of polarization, the rotation around Z axis was generated when the torsional vibration around Z axis mode was excited. And the rotation around X axis or Y axis was generated by combining the longitudinal vibration mode and the bending vibtration mode.
利用压电陶瓷在垂直极化方向平面内的变形，激励定子绕Z轴的扭转振动模态，实现转子绕Z轴的转动；激励在定子中固有频率接近、振动方向相垂直的伸缩振动模态和弯曲振动模态，并通过振动的叠加使定子末端质点产生绕X轴或者Y轴的椭圆运动，实现转子绕水平轴的转动。
-
Based on the equations, the contact spots on the face gear are simulated and analyses are conducted on the rule of the principal curvature of the contact points on the pinion and the face gear as well as the rule of the maximum press stress of the contact areas on the face gear.
根据布希涅斯克问题的求解方法，给出了传动中面齿轮上接触区域的椭圆长、短半径、中心最大变形量、最大压应力以及载荷分布的方程，分析了接触中心最大压应力的变化规律，实现了接触斑点的可视化仿真。
-
The undercutting analysis probe the position of undercutting line and the spherical angle of spherical gears. Teeth contact analysis probe the kinematic error and the position of contact point of spherical gears with misalignment and ideal case. Another contact pattern analysis probe the positions and size of contact pattern ofspherical gears.
齿面过切分析主要探讨球形齿轮之齿面过切位置及过切发生的球形角，接触分析则讨论球形齿轮分别在具有装配误差及理想状况时之运动误差及接触点位置，另外，齿印分析探讨球形齿轮在受力变形后其接触椭圆之位置及大小。
-
In the 1:250000 regional geological mapping of Yumenzhen, the authors studied deformation feldspar by long-short axis measurement method, compared with the deformation gravel, deformation amygdale, deformation relict long-short axis measurement, then found the both measurements were similar to deformation axis. It has been proved that deformation feldspar can be studied as to an area deformation characteristic of Yumenzhen.
在《1：25万玉门镇幅》调研的过程中，试以长石颗粒为研究对象，进行长短轴法变形测量，将其结果与相邻变形砾石、杏仁体和包体测量结果进行对比，发现它们具有相似的应变椭圆轴率，证实在变形花岗岩区可以用变形长石颗粒研究区域变形的特点。
- 更多网络解释与变形椭圆相关的网络解释 [注：此内容来源于网络，仅供参考]
-
nominal accuracy：标称精度
变形椭圆 indicatrix ellipse | 标称精度 nominal accuracy | 标称精度 nominal accuracy
-
ellipse of deformation：变形椭圆
ellipse 椭圆 | ellipse of deformation 变形椭圆 | ellipsograph 椭圆规
-
indicatrix ellipse：变形椭圆
变形观测控制网 control network for deformation observation | 变形椭圆 indicatrix ellipse | 标称精度 nominal accuracy
-
distortion isograms：等变形线
04.158 变形椭圆 indicatrix ellipse | 04.159 等变形线 distortion isograms | 04.160 投影变换 projection transformation