- 更多网络例句与发热源相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Monocrystalline silicon electrical heating element of this company is called the ideal product in high temperature and heating field in 21st century, which can substitute for the pollution pyrotoxin of traditional coal, heavy oil, natural gas.
公司新项目的产品二硅化钼电加热元件是被称为21世纪高温电加热领域的理想产品，可取代传统的煤，重油，天然气为热源的污染型发热源，是高温领域的环保替代品。
-
The structures of the thermoelectric couple and generator were described in detail in this paper. Also, the performance of the Radioactive Isotope Thermoelectric Generator was introduced, which has been used in space power, for example SNAP-7B RTG, SNAP-10A, GPHS-RTG.
本文对温差电偶的结构和温差发电器的构造作了详细的叙述，并且，对应用于航天的放射性同位素温差发电器作了介绍，比如SNAP-7B RTG、SNAP-10A系统、通用热源热电转换器。
-
The solution in the reactor has uniform inner heat source, and there are tiny air bubble built, the whole system is running by natural convection and the driving of air bubble. The gas-liquid two phase flow and heat transfer are mutual effecting to become the complex pyrology system.
堆内溶液是一个具有均匀内发热源，并伴随有微小气泡均匀生成的自然对流和气泡驱动同时作用下的三维复杂两相流动的物系，气液两相流流场与传热温度场相互作用，产生复杂的热工水力现象。
-
The main idea of this work is to find a thermal solution for Qosmio-F50 laptop computer of Toshiba company by performing numerical simulation first, and then, by verifying the result of simulation by molding tool equipped with heater. The developed design has been implemented into the product to prove the performance.
中文摘要本论文的研究主题，在针对东芝公司以上市之笔记型电脑Qosmio-F50，利用数值模拟软体为散热系统配置作先行规划分析，再以实际含发热源之模具，实际测试验证数值模拟结果的正确性，最后将设计导入实机。
-
Apart from the working limitations resulting from its structural property, the flat plate heat pipe carries out heat dissipation through the evaporation and condensation of the working fluid. Thus, if the working angle of the fluid is adverse to its backflow, the heat pipe will fail easily. Furthermore, not the orientations of all the heat sources are favorable to the functioning of the heat pipe. To compensate for this drawback, this research focuses primarily on the development of a composite structure which will reduce the effect of gravity on the working fluid. Generally speaking, the heat pipe is divided into three main categories: the groove type, sintered metal type and mesh screen type, as shown in Table 2. As far as capillary force is concerned, the sintered metal type and mesh screen type show better performance. As mentioned in R.
平板式热管除了因其结构特性而产生的工作极限之外，由于其作用乃是透过工作流体的蒸发及凝结进行散热，故若是其工作角度不利于液体之回流，便容易使热管失效，且并非所有之发热源都是位于有利于热管工作之位置，因此本研究之主要目的为设计一可减少重力对工作流体影响之复合式结构；一般而言，热管之结构大致可分为沟槽、烧结及网格三种(如表2所示)，其中烧结及网格结构有较佳之毛细力，在 R。
- 更多网络解释与发热源相关的网络解释 [注：此内容来源于网络，仅供参考]
-
pyrotoxin：热毒素,发热源
toxoid 变性毒素,类毒素 | pyrotoxin 热毒素,发热源 | antitoxin 抗毒素