参数变化

词组短语

parameter variation

与参数变化相关的网络例句 [注：此内容来源于网络，仅供参考]

The thesis can be divided into five parts as follows: First, the structural characteristics of finned-pipe evaporator are analyzed. After selecting suitable microelement controller, the heat-transfer and mass-transfer processes are analyzed for every microelement under the conditions of dryness, wetness and frostiness. Based on previous equations, some parameters of frostiness are confirmed and the frost-growing model is set up under frost condition. Some hypotheses are postulated and with the help of the equation of mass-conservation, energy-conservation and momentum-conservation, the evaporation model which fits in the dynamic simulation is built, which set a solid foundation for system simulation. Second, the starting and stopping behaviors under disturbed condition are analyzed and calculated by using the dynamic concentrative parameter model, which gives some advice to better prescribe refrigeration system and set theoretic foundation for carrying out automatic control of refrigeration system. Third, the normal running process is analyzed and calculated by means of rational matching theory, which gives some advice on how to better understand the parameter change under steady state and the affection of inlet-parameter on evaporator. Fourth, the simulation software with dynamic characteristic is designed, which can be applied to calculate thernio-parameter of cryogen, air humidity and frost thickness under different initial and boundary conditions, and to carry out dynamic simulation under conditions of dryness, wetness and frostiness, at the same time, to achieve detection and simulation at any stage from starting to stopping.

本文的主要内容如下：1对翅片管蒸发器结构特点进行分析，选取适当的微元控制体，就干、湿和霜工况下对每个微元分别进行传热传质分析，基于经验关系式确定霜的有关参数，对于霜工况下的霜生长建立模型，经适当假设，运用质量守恒、能量守恒和动量守恒方程建立适合动态仿真的蒸发器数学模型，为系统仿真奠定基础； 2对蒸发在大扰动下的开、停机过程，运用动态集中参数模型进行分析和计算，为更好地描述制冷系统运行的全过程奠定基础，同时也为制冷系统实现自动控制提供一定的理论基础； 3对蒸发器正常运行过程，运用动态分布参数和参数间定量耦合的观点来分析和计算，为更好地了解稳态工况下各点参数的变化情况及各入口参数对蒸发器动态特性的影响即蒸发器性能对各参数变化的敏感性； 4编写翅片管蒸发器动态特性仿真计算程序，可以计算不同边界条件和初始条件下的制冷剂热力参数、空气温湿度和霜厚度分布场，实现对翅片管蒸发器在干、湿和霜工况下的动态仿真。

For nonlinear harmonic oscillators, we close the flow equations and acquired an explicit expression of energy-level. For nonlinear-coupled harmonic oscillators, we close the flow equations and diagonalize the Hamiltonian by numerical analysis methods.

对非线性谐振子系统，计算出系统参数随流参数变化的一组方程及系统的能级；对耦合的非线性谐振子系统，得出系统参数随流参数变化的一组非线性方程，数值分析对角化了系统。

Thirdly, fuzzy control method and PID method were used respectively to design temperature self-adjustment controller of carbon fiber concrete laminate beam,by the MATLAB simulation it is found that the PID method has higher speed but is more sensitive to the fluctuation of system parameter ,it is suit to the regulating when the heat transfer coefficient fluctuates diminutively and the structure has little heat transfer with the environment;fuzzy control can be adapt to the parameter variety in a large scale , it is suit to the regulating when the heat transfer coefficient fluctuates greatly.

分别采用PID和模糊控制策略设计了温差自调节控制器，通过MATLAB仿真研究得出：PID方式具有更快的调节速度，但对系统参数变化较敏感，适合系统与外界对流交换较微弱，对流参数波动不大时的调节；模糊控制能够适应系统参数在较大范围内的变化，适合对流参数波动较大时的调节。

Aimed at the characteristic of multiple types of faults possibly happened in nuclear power plant, large scale of training sample, and requirement of quick and accurate diagnosing, after the analysis of large sample number generated by large fault type exceeds limitation of 64K paragraph in DOS and large number of local minmum in error surface, measurements of same format of data file, Win95/NT operating system platform, resetting weight learning rate, dynamic training set in quick learning algorithm and improvement on quick learning algorithm using homotopy method which can avoid local minmum points in error surface have been adopted to ensure quickly and effective process of the course of neural network's training and testing.

针对核动力装置可能发生的故障种类多，训练样本规模大，故障诊断需要快速准确的特点等，分析了样本多和故障种类多产生的训练样本量超出DOS段大小和网络误差曲面上局部极小值多的情况，采取了使用相同格式数据文件、Win95/NT操作系统平台，对快速学习算法采用重置神经网络权值学习率和动态训练集、并采用能够有效克服网络误差曲面上局部极小点的同伦方法对学习算法进行改进等措施保证神经网络训练测试过程的快速、有效地进行；针对装置发生的故障须快速、准确诊断的需要，分析了故障的产生对装置参数变化的影响及操纵员对故障诊断的基础，在核动力装置发生故障时参数曲线的变化量与正常运行时参数曲线的变化量存在明显差异的基础上，提出采用参数曲线的变化量作为神经网络的输入，并围绕参数变化量的方法采用二次曲线拟合滤波求变化量和阈值技术来保证神经网络得到精确的装置参数变化量，从而得到准确的诊断结果。

This article that focuses on the systematic and in-depth research in the current primal problem about abnormal burst pressure reservoir depress burst pressure has procured following main fruits:1 It forms the method which could obtain massive vertical static state mechanics parameters.2 In a foundation of acquisition of rock mechanics parameters,apply bent lamella that as mechanical model along with characteristic of actual geologic characteristics to analysis curvature for anticlinal strcture, get homologous tectonic stress value throug relation between the curvature and stress and different principal curvature in anticlinal structure,consequently set up laminational stress model for anticline reservoir. The block lamination for existed fracturing date has formed method of setting up mechanical model of lamination terrestrial stress by abtaining the block tectonic stress coefficients which are got by complex utilization test, laboratory test and fracturing date playback.3 Analysesing the main reason which lead to high burst pressure by considering the characteristic of reservoir geology,reservoir,and rock mechanics and reservoir damage,etc.Establishing burst pressure quantitative prediction model which provide gist for depressing construction risk and optimizing construction craft under the condition of open hole completion ,gun-perforated completion and damaged reservoir.4 Provding theoretical basis for interpreting acidification pretreatment which could depress busrt pressure by finding the relation between the influencing factors and rock machanics parameters and analysing the factors that have effect on rock mechanics parameters. Expounding the mechanism of reaction of mixed monomineral and acid from the angle of microcosmic element, evaluating quantitatively acid sensilility of different kinds of mineral effectively, and determing the first-order reaction dynamical equation of each mineral.5 Revealing rock mechanics property chage as a result of acid flooding in different condition by sandstone traumata experiment in different temperatures which combined with rock mechanics triaxial stress experiment.6 Associating damage mechanics with sandstone acidizing, established sandstone damage mechanics model in the foundation of the recognition on the rock mechanics parametric variation which is caused by acid-rock reaction in both macroscopic view and microscopic view ,also demonstrated those processes and quantitative estimated the acid busrt pressure to direct the site operation.

本文针对目前异常破裂压力储层降低破裂压力的主要问题展开较为系统和深入的研究，取得了以下主要成果：1形成了利用测井资料，结合室内岩芯测试结果，获取静动岩石力学参数的相关性特征，从而获得纵向上大量静态力学参数的方法。2在获取了岩石力学参数的此基础上，利用弯曲薄板作为力学模型，结合区块实际地质特征对背斜构造进行曲率分析，通过曲率与应力的关系，利用背斜构造不同部位的主曲率求得相应的构造应力值，从而建立起背斜储层的分层应力模型；对已有压裂资料的区块分层，形成了综合利用测试、室内实验、压裂资料反演获得该区块构造应力系数，建立起分层地应力的力学模型的方法。3综合考虑储层地质、油藏、岩石力学特性和储层伤害等因素，分析造成高破裂压力的主要原因，综合利用岩石力学、弹性力学等知识，建立了裸眼完井、射孔完井条件下以及储层受到伤害后的储层破裂压力定量预测模型，为降低施工风险和优化施工工艺提供了依据。4完成了物性、岩性影响岩石力学参数的因素分析，找出了各影响因素和岩石力学参数之间的关系，为从机理上解释酸化预处理降低破裂压力提供了理论基础；从微观元素的角度阐述了单矿物与酸反应的机理；并在此基础上，有效评价了各种矿物的酸敏感性，定量确定了岩石中各矿物的一级反应动力学方程。5完成了不同温度下的酸液类型、酸液浓度、注酸量等一系列砂岩损伤实验，结合岩石力学三轴应力实验，系统揭示了在不同条件下注酸而引起的岩石力学性质变化。6将损伤力学与砂岩酸化相结合，在宏观、微观两个方面认识酸岩反应引起岩石力学参数变化基础上，建立了砂岩损伤力学模型，并对其进行验证，在此基础上定量计算酸化后的破裂压力，有效指导现场施工

The characteristics of the filter include that the parameter variation ranges are taken into account, and within the parameter variation range each maximum magnitude of the residual vibrations is set to be equal. Thus, if the system parameters vary in lager ranges, the filter is more robust and the residual vibrations can be affectively eliminated.

该滤波器的特点是考虑了系统参数的变化范围，系统残留振动的最大幅值在参数变化区间内相等，从而提高了时滞滤波器的鲁棒性，特别是当系统参数大范围变化时，时滞滤波器有更强的鲁棒性，能有效消除柔性系统的残留振动。

The result shows that the changing law of saliferous reservoir parameters is a nonlinear relationship with several variables, and it is a very complicated process.

研究结果表明，高含盐油藏储层参数变化呈多元非线性函数关系，变化规律复杂；渗透率变化存在临界值，大于临界值时，渗透率随着驱替速度、驱替量和含盐量的增加而增大，小于临界值时，渗透率随着驱替速度、驱替量和含盐量的增加而减小；注入水性质会对参数变化过程有影响，而对最终变化结果无影响；盐的溶解是储层参数变化的根本原因，岩石颗粒的脱落和运移是储层参数变化的直接原因。

Referenced sub-drainage basins were selected in the upper reaches of the Madao main river way, and topographic parameters were obtained using software of River Tools in each sub-drainage. Monthly runoff simulations were then applied to them with the same parameters as Madao catchment, the responses of runoff simulation to topographic parameters were studied, and the Normalization of Runoff-total Length Index were presented. Analyses indicate that NRLI is influenced by source density. NRLI fluctuates tempestuously as source density decreases sharply.

在此基础上从马道出水站点沿主河道往上游再选取6个控制点，运用River Tools软件提取出各个控制点控制流域和地形参数，分析参数变化情况，并在此基础上用前面率定好的参数来模拟各个控制点处的出口流量，分析径流对地形参数变化的响应关系，并提出了归一化径流－河道总长比指数。

It unifies the variation of parameters and structure of system that leads to the variation of its time scale.

时间尺度的概念将对象参数和结构的变化导致系统快慢特性的变化统一在一起，所以控制器参数整定的时间尺度变换公式也给出了控制器对对象不确定的适应性和控制器对其自身参数变化的鲁棒性的新的涵义。

Results: Of the slight keratoconus group: the above indexes significantly decreased(P＜0.05). Of the moderate group: the above indexes, except for the apex decentration distance significantly decreased at 12 months and more evidently at 18 months. Of the severe group, the K value significantly decreased at 12 months and other figures remained unchanged. However, all the indexes significantly decreased except that the apex decentration distance remained unchanged at 18 months.

结果：轻度组，配戴RGPCL后角膜散光、锥顶K值、锥顶偏心距离、SRI、SAI较配戴前均有显著性降低（P＜0.05）；中度组，除12个月时锥顶偏心距离、角膜散光值较配戴前无显著变化外，其他各项参数亦有明显降低，18个月时下降更为明显；重度组，12个月时除锥顶K值显著减小外，其他参数变化不大，18个月时除锥顶偏心距离的变化不显著外，其他参数显著降低。

与参数变化相关的网络解释 [注：此内容来源于网络，仅供参考]

formation abrasiveness：地层研磨性参数

a lithological change 岩性变化 | formation abrasiveness 地层研磨性参数 | drillability factor 可钻性因素

anisotropy：各向异性[物理参数随方向的变化而变化]

anisotropic membrane各向异性膜 | anisotropy各向异性[物理参数随方向的变化而变化] | anitbacterial immunization抗(细)菌免疫

Evolution Options：控制噪波分形变化相位的具体参数,比如随机种子数量和是否循环变化等

Evolution:控制噪波分形变化相位 | Evolution Options:控制噪波分形变化相位的具体参数,比如随机种子数量和是否循环变化等 | Opacity:控制噪波的透明程度

Evolution Options：控制噪波形变化相位具体参数,比如随机种子数量否循环变化等

Evolution:控制噪波形变化相位 | Evolution Options:控制噪波形变化相位具体参数,比如随机种子数量否循环变化等 | Opacity:控制噪波透明程度

isotropy：各向同性[物理参数不随方向的改变而变化]

isotropic 各向同性的 | isotropy 各向同性[物理参数不随方向的改变而变化] | isotype 同种型

Mutate None：无变化,即关闭所有的变化

Mutate All:全部变化,使所有的参数随机变化. | Mutate None:无变化,即关闭所有的变化. | Bump Map:撞击图.

Mutate All：全部变化,使所有的参数随机变化

Genesis Editor映射:用来创建奇妙的、以球形为基础的形状,如星星、雪花等. | Mutate All:全部变化,使所有的参数随机变化. | Mutate None:无变化,即关闭所有的变化.

variety of parameter：参数变化

品种改良:variety improving | 参数变化:variety of parameter | 品种鉴定:Variety identification

Wire Parameters：(参数绑定)允许将一个物体与另一个物体的可动画参数绑定,同时变化

. Wire Parameters(参数绑定)::该命令共两个子菜单. 其... | . Wire Parameters(参数绑定)允许将一个物体与另一个物体的可动画参数绑定,同时变化. | . Parameter Wiring dialog(参数绑定对话框)定义参数绑定的各种关...

Parametric Deformers：(变化参数)

FREE FORM DEFORMEVS(自由形状专换) | PARAMETRIC DEFORMERS(变化参数) | SURFACE(表面)