- 更多网络例句与去毛刺相关的网络例句 [注：此内容来源于网络，仅供参考]
-
At last, the binary morphological opening operation was used to clean the burrs.
最后采用二值形态学开运算进行去毛刺处理。
-
The revitalization of round metal wire system are www.gangsilun.com.cn major wire brush wheels, wire brushes, brush, grinding wheel, grinding wheel peeling paint, brush deburring, paint stripping wire wheels, brush cutter, strip brush, chimney brush , round polished steel, with hole brush, roller, wire, polishing brush, metal brush, wire wheel, grinding wheel, wire wheel, wire brush, go paint wire wheels, wire brush stick, parallel brush , grinding wheel, parallel round, bowl-type wire wheels, steel wheel roller, brush springs, spring round brush, industrial brush .......
振兴钢丝轮五金制刷 www.gangsilun.com.cn 是专业钢丝轮，钢丝刷，笔刷，砂轮，剥漆砂轮，去毛刺刷，滚刷，脱漆钢丝轮，刀刷，条刷，烟筒刷，钢丝打磨轮，内孔刷，滚轮，钢丝滚刷，抛光轮，抛光刷，五金制刷，铜丝轮，打磨轮，钢丝砂轮，铜丝刷，去漆钢丝轮，钢丝棍刷，平行刷，打磨轮，平行轮，碗型钢丝轮，钢丝滚筒轮，弹簧刷，弹簧轮刷，工业用刷。。。。。。。
-
When the burrs are small and uniform, they are effective for robotic deburring.
当毛刺吗小而均匀，他们是有效的机器吗去毛刺。
-
So there is rod configurational change in the deburring process.
在去毛刺过程中会变形软化。
-
Therefore, this structure maintains a consistent rigidity and there is virtually no fiber rod configurational change during the deburring process.
因此，这种结构能够保证去毛刺过程中纤维坚固不变形，保持研磨的一致性
-
On the whole,burring this kind of bearing maintainer is realized by high efficiency and high quality.
传统的滚磨去毛刺加工，是将被加工零件和磨料自由地混合在一起，加工时
-
It was found that introducing 15 g/L additive containing 1.5 g saccharin helped to well retard electropolishing-induced corrosion of the electropolished improve the quality of the electropolished moldboard surfaces. At the same time, it was feasible to realize satisfactory precision electropolished of the laser moldboard made of stainless steel at a current density of 20~25 A/dm^2, duration of 1 min, and temperature of 60~65 ℃. The resulting polished moldboard had smooth walls and bright surface, while the corrosion was less than 0.005 mm.
结果表明，添加剂含量在15 g/L时能有效抑制抛光的腐蚀量，提高抛光质量；在精抛光的参数电流密度为20~25 A/dm^2，温度60~65℃，时间1 min条件下，钢片经去毛刺处理和精抛光处理能达到孔壁光滑、腐饮量小于0.005 mm的要求。
-
In this article, some problems in the application of several new technologies on de- burring and polishing machining in precise mechanical parts manufacture are summarized.
本文主要论述几种去毛刺与抛光加工的新工艺在精密机械零件加工与制造过程中应用。
-
The ensemble structure and working principle of clip electrochemical burring device are discussed in detail.
详细论述了夹片电化学去毛刺装置的总体结构、工作原理，整个装置由间歇往复输送机构、夹片模具、电解液循环装置和清洗装置组成，最后对间歇往复输送机构、夹片模具等进行设计计算。
-
Through adjustment of the width of the slot plus using turning process instead of milling process for bur removal with the addition of proper inspection method,for upgrading the quality of the joining parts,consequently avoiding fiber burring, yield going up from 92% to 99%.
分析了造成分梳辊体结合件挂花的原因，通过在实际中调整分梳辊辊体槽宽尺寸，改铣槽工艺为车槽工艺，增加去毛刺工序以及制定明确的检验方法来改进分梳辊体结合件加工质量，最终使其不挂花合格率由原来的92%提高到99%。
- 更多网络解释与去毛刺相关的网络解释 [注：此内容来源于网络，仅供参考]
-
removing burrs：去毛刺
193.倾卸 dump, tilt | 194.去毛刺 removing burrs | 195.扰动 disturbance
-
clear away burrs：去毛刺
焊后磨平 grinding to flat after welding | 去毛刺 clear away burrs | 回火 tempering
-
burring reamer：去毛刺铰刀
white mud thickener 白液沉渣洗涤器 | burring reamer 去毛刺铰刀 | safeguard construction 安全[防护]结构
-
burring reamer：去毛刺绞刀
burring machine 毛刺清理机 | burring reamer 去毛刺绞刀 | burrow rock drill 潜孔凿岩机
-
burring reamer：去毛刺手铰刀
burring mill 磨盘式磨粉机,磨盘式磨碎机 | burring reamer 去毛刺手铰刀 | Burroughs data access method 宝来公司数据存取方法
-
burring：去毛刺
burrhstone 硅质磨石 | burring 去毛刺 | burrless perforating 无毛口射孔
-
burring：去毛边去毛刺
burredge 粗边 | burring 去毛边 去毛刺 | burring 去毛边去毛刺
-
burring reamer：去毛刺手铰刀
burring mill 磨盘式磨粉机,磨盘式磨碎机 | burring reamer 去毛刺手铰刀 | Burroughs data access method 宝来公司数据存取方法
-
burring machine：去毛刺机
burring 去毛刺 | burring machine 去毛刺机 | bursting pressure 破裂压力
-
burnisher burring machine：去毛刺机
burnisher burr 毛刺 | burnisher burring machine 去毛刺机 | burnisher burst 突发突然破裂