- 更多网络例句与厚薄规相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Measure measure to choose to want correct current, measure to what car batholith cooperates clearance between each component choose feeler normally (feet of a place of strategic importance) or dial gauge.
测量量具选择要正确就目前而言，对汽车底盘各部件间配合间隙的测量通常选用厚薄规或百分表。
-
And dial gauge than feeler, its read a value accurate, but relatively difficult when the certain place of chassis is operated.
而百分表较之厚薄规，其读值准确，但是在底盘的某些部位操作时较为困难。
-
In implementation, a feeler gauge measures the thickness of the just-made sheet metal and sends this signal back to a servo-motor controlling the single variable of traction, the variable to affect the steel last, just before the rollers.
在实施过程中，由一个厚薄规测量刚刚制成的金属板的厚度，然后把信号传回一个伺服电动机以控制牵引力的单一变量——在卷板机之前最后影响钢板的变量。
-
In implementation, a feeler gauge measures the thickness of the just-made sheet metal and sends this signal back to a servo-motor controlling the single variable of traction, the variable to affect the steel last, just before the rollers.
在设立这些反馈装置的时候，是有一个厚薄规来测量刚刚作出的金属板的厚度，然后把这个信号传送回某种伺服电动机上，这个伺服电动机是用来控制一个单一变量，也就是牵引力——这个变量是在卷板机之前最后影响钢板的因素。
-
Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm. Repeat it for three release levers, their gaps should be the same, after that screw up the locking nuts, and check it to make sure.
b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍。
-
B. Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm.
b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍
- 更多网络解释与厚薄规相关的网络解释 [注：此内容来源于网络，仅供参考]
-
automatic screwdriver：电动启子
forklift叉车 | automatic screwdriver电动启子 | thickness gauge厚薄规
-
automatic screwdriver：电动启子 thickness gauge厚薄规
automatic screwdriver电动启子 thickness gauge厚薄规 | power wire电源线 | buzzle蜂鸣器
-
caliber gauge：外径卡规, 厚薄规
caliber compasses | 弯脚圆规, 微调小圆规 | caliber gauge | 外径卡规, 厚薄规 | caliber radius head | 弹头蛋形部曲率半径(以口径为单位)
-
alignment feeler：对准测隙规, 对准厚薄规
proportioning motor 比例电动机 | alignment feeler 对准测隙规, 对准厚薄规 | trace drawing 描图
-
feeler gage：厚薄规
虹吸注油器 syphon lubricator | 厚薄规 feeler gage | 厚透镜 thick lens
-
thickness gauge：厚薄规
automatic screwdriver电动启子 | thickness gauge厚薄规 | power wire电源线
-
feeler; finger gauge：厚薄规
加油器;馈[电]线 feeder | 厚薄规 feeler; finger gauge | 毛毡 felt
-
thickness piece：厚薄规
thickness of shaft flange 轴法兰厚度 | thickness piece 厚薄规 | thickness piece 厚度规
-
thickness feeler gauge：测隙规,厚薄规
thickness difference;厚度差 | thickness feeler gauge;测隙规,厚薄规 | thickness gauge;厚薄规
-
feeler gauge reading：厚薄规读数
feeler gauge;厚薄规 | feeler gauge reading;厚薄规读数 | feeler rod;厚薄规杆