压圈

词组短语

clamping ring

与压圈相关的网络例句 [注：此内容来源于网络，仅供参考]

Gyrator pressure through the two semi-circular ring mounted on the transfer case on the ring nut can loosen pressure drilling within 360 ° angle in any adjustment.

回转器通过两只半圆压圈装于分动箱上，松动压圈螺母可对钻孔倾角在360°范围内任意调整。

The hoses are mounted at the customer's plant with spring clip clamps; the tubing and couplings are fitted with press rings at the ContiTech plant.

胶管在客户工厂用弹簧夹安装；管件和连接件在康迪泰克工厂用压圈装配。

This paper introduces the reason that the damper bars of the squirrel-cage rotor is easy to break, compares and analyzes the cases of fitting the fans on the end ring s and fitting the fans on the other site, The result shows that the number of broken bars can be reduced by fitting the fans on the clamp ring.

本文指出了转子断条现象，研究了断条原因，对端环上挂风扇与不挂风扇的情况进行了分析比较，并指出采用风扇挂在压圈上的结构，可减少断条事故的发生。

Our main production vehicles, motorcycles of the cable car metal stamping parts and stainless steel wheel covers, Houcang door hinge, fuel tank cover hinges, tires movements, Bian Sugan Fangchen Zhao pressure ring, which Lasso metal stamping items 200 Many types, special high-tensile equipment, the maximum capacity of parts to 110 MM, and I can contract various plants more difficult car metal stamping parts (Independent Development and Design), the largest equipment-pressure reached 315 tons.

本厂主要生产汽车、摩托车拉索的五金冲压件和汽车不锈钢轮罩、后舱门铰链、油箱盖铰链、轮胎升降器、变速杆防尘罩压圈等，其中拉索五金冲压件产品有200多种类型，特制高拉伸设备，最高零件可生产到110MM，而且我厂可以承揽各种难度较大的汽车五金冲压件，最大设备冲压力达到315吨。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果展开平板在压边圈面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈表面间的平衡块；压边圈的变形。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

褶皱起因于不充分的拉伸或失去控制的压缩变形。如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

QFS type turbogenerators have some original problems , such as large magnetic lenkage at the end winding due to configuration , higher local temperature of stator s end press ring, incapable of leading phase operation and low efficiency of generator, not matching capacity of the 335MW steam turbines etc, it is necessary to uprate and retrofit the 300MW QFS type turbogenerator.

该型发电机组存在着因结构原因端部损耗较大、端部压圈局部温度较高、不具备进相运行能力、发电机效率低以及发电机与改造后的汽轮机容量不匹配等问题，必须进行增容改造。

The results show that increasing the pressure in flow system by using a back pressure coil is the simplest way to eliminate air bubbles.

讨论了消除流路体系中气泡的方法，指出用反压圈增大流路体系的压强是消除气泡干扰最简便的方法，并列举了用反压圈消除气泡的实例。

Seal leak link Office Reason: 1, ring rolling strict 2, seals and body welding, surfacing of poor quality; 3, ring connecting thread, screw, loop loose; 4, ring connection and corrosion.

堆焊处无法补焊时应清除原堆焊和加工； 3、卸下螺钉、压圈清洗，更换损坏的部件，研磨密封与连接座密合面，重新装配。

与压圈相关的网络解释 [注：此内容来源于网络，仅供参考]

blank holder：压边圈

2.4.16 压料板 pressure plate | 2.4.17 压边圈 blank holder | 2.4.18 齿圈压板 serrated ring

choke：抗流圈

即可享受优美的音乐飨宴,5坪以内的空间都可以获得相当不错的音压,真空管音质细腻圆润,人声突出,适合纯音乐的聆听,体积小巧,书房或卧室皆相当容易摆放,扩大机采用全手工搭棚制作,充足的电源供应,并采用抗流圈(CHOKE)滤波,声底十分乾净,

smoothing choke：滤波扼流器;平流扼流圈

辘压;滚压 rolling | 滤波扼流器;平流扼流圈 smoothing choke | 滤波电容器;平流电容器 smoothing capacitor

core clamper：铁心压板,铁心压圈

堆心回路,铁心磁路 core circuit | 铁心压板,铁心压圈 core clamper | 铁心固定,铁心夹紧 core clamping

Knit cam;Stitch cam：弯纱三角,成圈三角

15)脱圈三角Knock-over cam | 16)弯纱三角,成圈三角Knit cam;Stitch cam | 17)弯纱三角调节器,压针三角调节器Stitch cam regulator

pressure hull shell ring：耐压壳圈

pressure hole 测压孔 | pressure hull shell ring 耐压壳圈 | pressure hull 内壳

band pusher：压圈器

bandpass filter 带通滤波器 | band pusher 压圈器 | band removing pliers 拔圈钳

Binder Ring：压边圈

Bezier spline|贝塞尔样条 | Binder Ring|压边圈 | Blank|隐藏

bearing cup inserter set：轴承杯(外座圈)全套压入工具

bearing cover || 轴承盖 | bearing cup inserter set || 轴承杯(外座圈)全套压入工具 | bearing cup inserter || 轴承杯(外座圈)压入器

chuck ring：夹圈, 锁紧环, 压环

chuck plate || 夹盘 | chuck ring || 夹圈, 锁紧环, 压环 | chuck roast || 肩部厚肉块(除去近颈部的肩肉)