- 更多网络例句与功率增大相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The results show that the shape of meniscus is non-homogeneous because of the structure of the rectangular mold, and the height of meniscus will enlarge as increasing the power, and at the same time the meniscus fluctuate aggregately. The coil should be placed near the top of the mold and the initial free surface level should be placed in the middle of the coil in practice.
结果表明：由于矩形电磁软接触结晶器本身的结构限制，其弯月面沿周向上的分布具有不均匀性；随电源功率增大，弯月面高度增大，同时波动加剧；实际生产中线圈应尽量靠近结晶器口部位置安装，有利于提高弯月面高度和增强弯月面稳定性；浇注过程中，应该使浇注液面尽可能的控制在线圈中心偏上位置；当电源频率增大时，应该同时适当的提高电流来保证软接触效果。
-
To the same kind of rocks, the penetration rate increases with the increases of electric bit thermal power. When electric bit thermal power keeps fixedness, the penetration rate increases in various degrees with the increases of bit load in difference rocks. Increasing the bit load is beneficial to improve the quality of glass hole wall, but the bit load should not be too big.
对于同一种岩石，钻进速度随钻头电热功率的增大而增大；当钻头电热功率不变时，根据所钻岩石岩性的不同，钻进速度随钻头轴载的增大而不同程度地增大，增加钻头轴载有利于提高玻璃状孔壁的质量，但不宜过大。
-
The result indicates that the output power oscillates and weakens along with increasing input power,and its oscillation period depends on the distance between the medium and beam focal point.Limiter′s limiting ability will decrease if waist size of the incident Gaussian beam and the aperture size increase.With a fixed input power scope,medium′s best limiting position will move towards the focal point if waist size of Gaussian beam and the aperture size increase,but the best limiting position will change a lot with different input power scopes.
结果表明：限幅器的出射功率随入射功率的增加衰减振荡，其振荡周期取决于介质相对于光束焦点的位置；限幅器的限幅能力随入射光束腰半径和光阑孔径的变大而减弱；入射功率范围固定，入射光束腰半径和光阑孔径增大时，介质的最佳限幅位置向入射光束的焦点靠近，但是在某些入射功率范围内会存在多个最佳限幅位置；光限幅器的箝位输出功率随光阑线性透过率的增加存在线性增加和非线性增加两个不同区域，实际应用中应在线性增加区域确定光阑孔径的大小。
-
The study results indicate that as emission power increases, the peak power density on the section of a certain distance will increase firstly, then it will descend and that the peak light intensity on the section will increase with the increasing of spot radius of basic mode Gaussian beam. As the propagation distance increases, the peak light intensity on the section will descend gradually, and the laser energy will spread. The light intensity distribution exhibits straw hat shape on a certain conditions, in other word to say, the central light intensity is less than acroteric light intensity.
结果表明，无风稳态热晕效应存在时，随发射功率的增大，一定传输距离截面上的峰值功率密度先增人后减小；截面上的峰值光强随基模高斯光束的腰斑半径的增大而增大；随着传输距离的增大，截面上峰值光强在逐渐减小，能量在逐渐向周围扩展；在一定条件下，截面上的光强分布会呈现中心光强小于周围光强的&草帽型&分布。
-
The experimental results are shown that the microstructure of QT600-3 by CO_2 laser quenching is Aphanitic Martensite+Graphite,and residual stresses are all compressive,which is above 120 MPa,they increase with laser power.
结果表明：经CO_2激光淬火后QT600-3的显微组织为隐晶马氏体+石墨，残余应力均为压应力，其值在120 MPa以上，且随着功率的增大而增加；相变层深度随着扫描速率和光斑直径的增加而减小，且随着功率的增大而增加；激光淬火后的材料组织结构比较均匀，有利于提高凸轮轴的使用寿命。
-
When increase the ultrasonic power, the ultrasonic density and solute athletics rate all increase, intensify the impact which made in ultrasonic cavitation and corrade degree to gesso, heighten the decomposition ratio.
当超声波功率增大，超声密度就越大，溶质分子运动速度增加，强化空化产生的冲击流，对磷石膏的侵蚀力度也加强，因此提高磷矿分解率。
-
Under the limitative temperature, the bending angle is increased with the increase of laser power and decreased with the increase of scanning velocity and laser spot.
在限定的温度条件下，弯曲角度随激光功率的增大而增大，随扫描速度和激光光斑的增大而减小。
-
The influence of its main design parameters on the floating displacement is analyzed.These provide theoretical background for the design of the basic floating parts of the star gear train.The floating displacement of center gears does not change with the power change of the train,and increases with the increase of the rotational speed of the train...
分析表明，中心轮的浮动位移量不随系统输入功率的变化而变化，随系统转速的增大而增大；中心轮的浮动位移量随系统星轮个数的增加而增大，随系统构件误差值的增大而增大，各构件的误差值对中心轮的浮动位移量的影响有累加作用；中心轮的浮动位移量随其齿轮的质量及转动惯量的增大而增加。
-
This paper experimentally studied smash characteristic of com straw, including mainly performance parameter of pulverizer such as consumption of electricity per ton, hour productivity and hammer patch thick under the condition of different moisture rates and sieve pore diameter .
本文主要对不同含水率、筛孔直径下粉碎机的吨料电耗、小时生产率及锤片厚度等性能参数进行了玉米秸秆粉碎特性试验研究，结果表明：对于相同筛孔直径，随着含水率的增大，负荷输入功率基本不变，吨料电耗增加，生产率降低；对于相同含水率的玉米秸秆，随着筛孔直径的增大，吨料电耗、负荷输入功率降低，小时生产率增加；度电产量和粉碎效率随着锤片厚度的减薄而增加，当锤片厚度为4mm时，既能够保持较高的粉碎效率，又保证了一定的耐用度。
-
For pump power, with the liquid viscosity increases, lift and efficiency, shaft power increases, so sometimes on industrial liquid viscosity viscous heating to make smaller in order to improve transmission efficiency.
对于动力式泵，随着液体粘度增大，扬程和效率降低，轴功率增大，所以工业上有时将粘度大的液体加热使粘性变小，以提高输送效率。
- 更多网络解释与功率增大相关的网络解释 [注：此内容来源于网络，仅供参考]
-
damper：挡板
另外挡板(Damper)使用将弹性体(Elastomer)注射模塑成形的材料,使挡板的刚性保持一定水平的形状. 其结果,由于可以增大振动板的振幅,从而使输出功率提高为5W,高于过去的3W. 除此之外,该产品还采用了使开口(Port)内的空气容易流动的形状,
-
hum：哼声
并反相串联而成的(但也有些结构比较特殊的双线圈拾音器)串联的目的是增大整个拾音器的输出功率,而反相连接的目的则是减少一般单线圈拾音器所固有的噪音,即哼声(hum)这些噪音一般是由照明系统、建筑配电以及放大器变压器的电磁干扰(我们知道,
-
turbo：增压发动机
涡轮增压发动机(Turbo)增压技术是一种提高发动机进气能力的方法. 它通过采用专门的压气机,预先对进入气缸的气体进行压缩,提高进入气缸的气体密度,增大进气量,更好地满足燃料的燃烧需要,从而达到提高发动机功率的目的.