- 更多网络例句与切线应力相关的网络例句 [注：此内容来源于网络，仅供参考]
-
It is found that in certain water ratio and consolidation pressure, the values of initial elastic modulus and principal deviator stress increase with intermediate principal stress increasing; in certain intermediate principal stress, the values of initial elastic modulus and principal deviator stress increase with water ratio falling.
试验结果表明：在一定的含水率和固结压力下，偏差应力和初始切线模量均随中主应力比b的增大而增大；在中主应力比b确定的情况下，偏差应力和强度最大值随着含水率的增大而减小。
-
At the same time, under the condition of small strain, firstly, the secant shear modulus was always larger than the tangent shear modulus. Secondly, when the logarithmic coordinates were applied to describe shear strain, the decrease of shear modulus with shear strain could be expressed by reversed S shape curve with two inflexion points, and through analyzing and validating, the deduced equation could perfectly reflect this characteristic. Finally, different stress paths and strain areas would lead to different attenuation trends.
而且，在小应变范围内，割线剪切模量总是大于切线剪切模量；当剪切应变采用对数坐标表示时，剪切模量随着剪切应变的增加而衰减，且衰减的规律都可以表示为带有两个拐点的反S型曲线，经分析验证本文所得公式3可以对此特性进行很好地反映；但应力路径、应变范围不同其衰减幅度不同。
-
Increase of 47% in the unconned compression strength compared to increase of 26% in the secant modulus at the maximum stress level, 25% in the secant modulus at half of the maximum stress level, and 23% in initial tangent modulus.
这一变化的数额膨润土10日至15 ％，导致平均增加了47 ％的无侧限抗压强度相比增加了26 ％的割线模量的最高应力水平， 25 ％的割线模量的一半的最大应力水平， 23 ％的初始切线模量。
-
In Particular, the tangent stiffness matrix in the incremental relation becomes symmetric, ensuring the efficiency in the numerical analysis, whereas the integrated constitutive relation serves as a guide, ensuring the convergence on the physically feasible stress strain relation.
值得一提得是，增量本构方程中的切线劲度矩阵是对称的，使得在进行数值分析时十分有效。而全量本构方程作为确保实际可行的应力应变滞回圈收敛的向导。
- 更多网络解释与切线应力相关的网络解释 [注：此内容来源于网络，仅供参考]
-
tilting concrete mixer：翻滚转动式混淆机
tangential stress 切线应力 | tilting concrete mixer 翻滚转动式混淆机 | tractor loader 拖拉机式装载机
-
Dens：密度
用MP命令输入弹性模量(Exx),密度(DENS)和泊松比(NUXY). 用TB,PLAW,,,,8和TBDATA命令的1-7项输入屈服应力、切线模量、失效的有效真实塑性应变、应变率参数C、应变率参数P、定义有效全应力相对于有效塑性真应变的载荷曲线ID 以及定义应变率缩放的载荷曲线ID.
-
EX：弹性模量
--这些模型都用弹性模量(EX)和切线模量(ETAN)来表示材料的应力-应变关系. --初始速度(EDIVELO)与刚体定义(EDMP,RIGID)是显式分析所独有的. --质量加权(alpha)和刚度加权(beta)阻尼可以用EDDAMP命令施加.
-
tangent shearing stress：切线应力
直通板列 through strake | 切线应力 tangent shearing stress | 换接开关 transfer switch
-
tangential stress：切线应力
tangential speed 切向速度 | tangential stress 切线应力 | tangential stress 切向应力
-
tangential stress WESTBANK：切线应力
tangential reaction WESTBANK 切线反力 | tangential stress WESTBANK 切线应力 | tangential velocity WESTBANK 切线速度
-
maximum tangential stress：最大切线应力
最大切应力 maximum shear stress | 最大切线应力 maximum tangential stress | 最大容水量 maximum water-holding capacity
-
tangents method：切线法
tangential stress 切向应力 | tangents method 切线法 | tape 纸带
-
circumfluence：周流,环流
切线应力,周向应力 circumferential stress | 周流,环流 circumfluence | 外接圆(数学) circumscribed circke
-
maximum shear strain：最大切应变
最大切应变 maximum shear strain | 最大切应力 maximum shear stress | 最大切线应力 maximum tangential stress