凹入

基本解释 (translations)

indrawing  ·  invagination  ·  invaginat

与凹入相关的网络例句 [注：此内容来源于网络，仅供参考]

The results show that the degassing efficiency increases with the residence time increasing;when other parameters are certain, the degassing efficiency increases with the number of arris and the concave depth increasing;the degassing efficiency decreases with the angle increasing.

结果表明：脱气效率随着滞留时间的增大而增大；当其他参数一定时，脱气效率随着棱数和凹入深度的增大而增大，随着角度的增大而减小。

A cylinder is a hollow tube with a closed concave base that permits it to stand up right.

钢瓶是中空的管道，封闭的底部是凹入的，这样可以直立起来。

A cylinder is a hollow tube with a closed concave base that permits it to stand upright.

钢瓶是中空的管道，封闭的底部是凹入的，这样可以直立起来。

A cylinder is a hollow tube with a closed concave base that permits the cylinder to stand upright.

钢瓶是中空的管道，封闭的底部是凹入的，这样可以直立起来。

Is a hollow tube with a closed concave base that permits the cylinder to stand upright.

钢瓶（图1）是中空的管道，封闭的底部是凹入的，这样可以直立起来。

With the corresponding flow parameters measured through the experiments and the criterion equation mentioned above,the correlation formula of degassing efficiency of flow of gas/liquid two-phase flow through corrugated multicup isoflux gas anchor is obtained through the regression analysis using the least square method and the Gaussian elimination.The influences of the number of arris and concave depth and angle on degassing efficiency are analyzed.

利用量纲分析方法建立了气液两相流体在瓦棱状多杯等流型气锚中流动的准则方程；根据室内实验测得相应参数和准则方程，利用最小二乘法及高斯消去法进行回归分析，得到气液两相流体在瓦棱状多杯等流型气锚中流动时脱气效率的关联公式，并分析了棱数、凹入深度、角度对脱气效率的影响。

Back rounding: Forming the back of a book into a convex curve and thus the fore-edge a concave curve which makes the turning of pages more easy.

圆脊：把书脊做成凸起的圆弧，书口则是凹入的圆弧，方便翻阅。

"F" is the distance between point P' and the tangent to the concave area in the maximum point of concavity measured in projection view on the plane of symmetry Y.

"f"为在对称面Y上的投影视图上测量的点P'和最大凹状点上的对凹入区域的切线之间的距离。

The piezoelectric motor includes a piezoelectric member which generates a first vibration mode and a second vibration mode simultaneously by an applied power and a frictional member of which a portion is insertedly attached into a concave portion indentedly formed on one side of the piezoelectric member, wherein the frictional member is in an elliptic motion by the vibration generated by the piezoelectric member, so that an influence of the attachment of the frictional member to a resonance frequency can be minimized.

该压电电机包括：压电构件，通过施加的功率同时产生第一振动模式和第二振动模式；摩擦构件，摩擦构件的一部分插入地附着到凹入地形成在压电构件的一侧上的凹入部分中，其中，摩擦构件通过由压电构件产生的振动进行椭圆运动，从而能够使附着摩擦构件对谐振频率的影响最小化。

The stripper may also be used to form slight indentations or re-entrant curves in the botton of a cup, with or without a flange.

脱衣舞娘也可以用来形成轻微凹入或重入曲线在底部的杯，或无凸缘。

与凹入相关的网络解释 [注：此内容来源于网络，仅供参考]

incurvate：凹入的

Incurvarioidea穿孔蛾总科 | incurvate凹入的 | incurvation内曲

indrawing：凹入

indraught引入 | indrawing凹入 | Indriidae大狐猴科

invaginate：凹入

invadingwavesinestuary 河口入侵波 | invaginate 凹入 | invagination 凹入 内陷 反折 折入 套迭

invagination：凹入,折入,套叠

introscope 内腔检视仪,内孔窥视仪 | invagination 凹入,折入,套叠 | invasive 侵害的,侵入的

re-entrant mold：凹入模

rapping rod 起模杆 | re-entrant mold 凹入模 | retainer pin 嵌件梢

stepped bulkhead：凹入舱壁

stepped bottom 阶形底 | stepped bulkhead 凹入舱壁 | stepped bulkhead 阶形舱壁

invaginated：凹入

偶然接种,意外接种 invaccination | 凹入 invaginated | 濒死肠套迭 invagination,agonal

Recessed：凹入

Ramp 倾斜 | Recessed 凹入 | Right foot 右脚

reentrant face wall：凹入曲面壁

reentrant code 重入 码 | reentrant face wall 凹入曲面壁 | reentrant library 重入库段

re-entrant：凹入的

redundancy 过多 | re-entrant 凹入的 | refer 指,涉及,谈及