- 更多网络例句与凸面体相关的网络例句 [注：此内容来源于网络，仅供参考]
-
A convex surface, body, part, or line.
凸面、凸面体、凸面部分或凸线
-
The processes of 3D buffer creation for point, line, face and convex polyhedron are introduced in detail in the paper.
详细论述了点，线，面和凸体的三维缓冲区生成过程。
-
Give a projecting plane,sign volume of pentahedron for each triangle in mesh,which is constructed by the triangle and it projection in projecting plane,is computed.Volume of the mesh is algebraic sum of all pentahedrons' signed volume.Triangles will be partition into several smaller triangles when necessary.
该方法通过指定投影平面，计算每个三角面片及其在投影平面上的投影所围成的凸五面体的带符号体积（必要时对三角面片进行细分），整个模型的体积为所有凸五面体带符号体积的代数和。
-
The shapes of the melting solid surface may be concave, convex or plane, while the perimeter of plane contact regions may be rectangular, circular, elliptical, parabolic and arc curve. The types of relative motion reviewed here are the movement of a solid PCM melting inside a heated capsule, the movement of a hot body through a melting solid medium, slide contact and rolling contact. The contact melting may be caused by temperature difference, pressure difference, friction and viscous heating. Finally, the research regions in the future are summarized.
内容包括各种形式的接触熔化，可归纳为：在接触形状上可以有凹、凸与平的面，而接触的周长可以是矩形、圆形、椭圆形、抛物线形与弧形曲线；相对运动的类型有固体相变材料在加热容器内熔化，加热体通过熔化固体介质的运动，滑动接触与滚、转动接触；引起接触熔化的原因有温差、压力差、摩擦与粘性热。
-
Finally, the surface hardness and metallographical structure were measured and analyzed. The results show: the surface hardness of slight protuberance than the matrix has been improved by 30%-40%.
最后对毛化模具表面硬度和金相组织状况进行了测量和分析，结果表明，微凸体表面硬度比基体材料的表面硬度提高了30%-40%。
-
Based on the quadratic separator, the design of a robust reliable tracking controller is investigated for a class of polytopic systems with actuator failures.
针对含执行机构故障的凸面体不确定系统，本文基于二次型分离算子给出了一种鲁棒可靠跟踪控制器的设计方法。
-
Based on a quadratic separator, a robust reliable filter design method for a class of systems with polytopic type uncertainty is presented against sensor failures.
摘要针对凸面体不确定系统并考虑传感器发生故障的情况，基于二次型分离算子进行了鲁棒可靠滤波器设计的研究。
-
The unetched specimens were instantly observed by QUANTA-400 environment scanning electron microscope,scanning tunnel microscope and optical microscope,respectively.The results show that the surface relief will be found during the bainite transforming and will be in the shape of "Λ".The formation of bainite surface relief is to ...
不经浸蚀，分别采用QUANTA-400环境扫描电镜、Nanofrist-1000扫描隧道显微镜和光学显微镜观察试样，发现，贝氏体相变过程中产生了表面浮凸，表面浮凸为&帐篷形&，并认为贝氏体表面浮凸的产生，是由于过冷奥氏体转变为贝氏体时比体积增大，且试样表面层体积膨胀不均匀造成的。
-
In order to improve the efficiency of the collision detection for two convex polytopes, this paper proposes a fast projection-separation approach.
为了有效地提高凸面体之间的碰撞检测效率，提出一种凸多面体快速碰撞检测的投影分离算法。
-
Cavities are specific electromagnetic structures, and their scatterings are different from convex objects.
凹形腔体是一类特殊的电磁散射结构，其电磁散射特性不同于一般的凸面体。
- 更多网络解释与凸面体相关的网络解释 [注：此内容来源于网络，仅供参考]
-
convex ridging body：长凸面起垄犁体(使起垄前的肥料集中在垄的中部)
convex region | 凸区域 | convex ridging body | 长凸面起垄犁体(使起垄前的肥料集中在垄的中部) | convex sequence | 凸序列
-
convex ridging body：长凸面起垄犁体
convex programming problem 凸性规划问题 | convex ridging body 长凸面起垄犁体 | convex round moulding 凸圆线脚
-
mandible：下颌骨
下颌骨(mandible)位于上颌骨下方,分为水平部分的体和两侧垂直的支. 体呈弓状,下缘光滑,上缘生有下牙槽. 外面光滑,前方正中部向前的隆起叫颏隆凸,由此向外侧,在对第三颗牙槽下方处有颏孔. 在体的内面中线处有尖锐的突起叫颏棘,其下方两侧各有一线窝
-
neural arch：髓弓
躯干椎第一椎较小,髓弓( neural arch )及髓棘 ( neural spine ) 也较短,椎体前凸后凹,凹出面嵌人基枕骨后面的凹陷处,凹入两侧与第二椎的椎体相关节. 髓弓的前关节突( preZygapophysis )与基枕骨凹陷面上方的一对小型突起相关节,
-
Neural spine：髓棘
躯干椎第一椎较小,髓弓( neural arch )及髓棘 ( neural spine ) 也较短,椎体前凸后凹,凹出面嵌人基枕骨后面的凹陷处,凹入两侧与第二椎的椎体相关节. 髓弓的前关节突( preZygapophysis )与基枕骨凹陷面上方的一对小型突起相关节,
-
bulking factor：体积扩张系 ;体胀系
bulkhead lighting fittings 凸面照明器 | bulking factor 体积扩张系 ;体胀系 | bulldozer 推土机;铲