英语人>词典>汉英 : 凸模 的英文翻译,例句
凸模 的英文翻译、例句

凸模

词组短语
force plug
更多网络例句与凸模相关的网络例句 [注:此内容来源于网络,仅供参考]

According to the results, the contour of cross section is related to the relative radius of punch; the maximum equivalent plastic strain is an increasing function of it and the ellipticity is a decreasing function of it.

研究结果表明,成形件的横断面轮廓形状与相对凸模半径有关;最大塑性等效应变是相对凸模半径的递增函数;椭圆度随相对凸模半径的增加而减小。基於研究结果,本文给出了相对凸模半径的设计原则。

Using bevelled punch and step punch in blanking die, carried on the rational distribution to blanking force, reduced the blanking force well which the press equipment need, and the question of insufficient press equipment pressure was solved.

在冲裁模中结合使用斜刃凸模和阶梯凸模,对冲裁力进行合理分配,很好地降低了冲压设备所需的冲裁力,解决冲压设备压力不足的问题。

On the scale of punch and die with punching and bending die punch; Die positioning pulled positioning and bending Die top two pieces of equipment; 6 punch with epoxy fixed on the next model, since blanking punch and bending die role.

上模为凸凹模起冲裁凹模和弯曲凸模作用;模具中定位板起定位和弯曲凹模顶件装置两种作用;六个凸模用环氧树脂浇注固定在下模上,起冲裁凸模和弯曲凹模作用。

In the standard designing procedure of stamping die , the calculation formulas of dimensions of both punch and die plate are derived based on such a principle that for blanking operation to produce the punch with the die plate as the basic part, and for the punching operation to produce the die plate with the punch as the basic part.

在冲裁模设计中,冲裁模的凸模、凹模刃口尺寸计算公式是根据落料以凹模为基准件配制凸模,冲孔以凸模为基准件配制凹模的原则建立的。

The general process of reverse engineering for the punch block of a welding die for shadow mask was stated,including the digitization process of solid mass by using three-dimensional measuring machine,the 3D modeling and surface reconstruction by using Pro/E.

以荫罩焊接模凸模为例介绍了逆向工程的一般过程,采用三坐标测量机进行了实体的数字化过程,使用Pro/E进行了荫罩的3D建模和曲面重构,完成了荫罩焊接模凸模设计,并用Mastercam进行了荫罩焊接模凸模的加工模拟,最后安排工艺流程完成了荫罩焊接模凸模的实际加工。

In this design introduced the transmission covers the punch holes the ramming craft analysis, the craft plan formulation, arranges the specimen map design, the always ramming strength computation and the center of pressure computation, the cutting edge size computation, the spring, the rubber computation and selects, the raised mold, the concave mold or the convex-concave mold structural design and all that die the components structural design, draws up the mold assembly drawing and the work detail drawing, the compilation design instruction booklet, fills in the ramming craft card and the work components machine-finishing technological process card, raised pays attention to, the concave mold coordinate processing.

本设计中介绍了传动盖冲孔的冲压工艺分析,工艺方案的分析和制定,排样图的设计,总的冲压力计算及压力中心的计算,刃口尺寸的计算,弹簧的计算和选用,凸模、凹模或凸凹模结构设计以及其他冲模零件的结构设计,绘制模具装配图和工作零件图,编写设计说明书,填写冲压工艺卡和工作零件机械加工工艺过程卡,注意凸、凹模的配合加工。

In this design introduced the transmission covers the punch holes the ramming craft analysis, the craft plan formulation, arranges the specimen map design, the always ramming strength computation and the center of pressure computation, the cutting edge size computation, the spring, the rubber computation and selects, the raised mold, the concave mold or the convex-concave mold structural design and all that die the components structural design, draws up the mold assembly drawing and the work detail drawing, the compilation design instruction booklet, fills in the ramming craft card and the work components machine-finishing technological process card, raised pays attention to, the concave mold coordinate processing.

摘要本设计中介绍了传动盖冲孔的冲压工艺分析,工艺方案的分析和制定,排样图的设计,总的冲压力计算及压力中心的计算,刃口尺寸的计算,弹簧的计算和选用,凸模、凹模或凸凹模结构设计以及其他冲模零件的结构设计,绘制模具装配图和工作零件图,编写设计说明书,填写冲压工艺卡和工作零件机械加工工艺过程卡,注意凸、凹模的配合加工。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

原文对于寒冲压技术的合种、特征及开展圆背做砬简单概述;阐述了冲压整机的构成本理、基础模具构造与活动进程及其设计本理;对典范的冲压件模具进佳的了设计:大曲径三通管冲压复合模设计掀世了大直径三通管的减工困难、带无沉动凸凸模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、长音器后挖碗落料、拉深、冲孔、翻边复合模设计、一模二件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链舒方成形工艺及模具设计、半自动送料切角安装设计、涩板式送料拉深、冲孔、翻边模设计完成自动送料、长管少孔冲模设计、带凸缘台阶方盒形整件拉深模战盒形件正壁小孔翻孔模。

Also analyzes the mold of the main components (such as punch and die and dump devices, drawing punch, slates, Punch plate, etc.) design and manufacturing, stamping equipment selection, punch-gap adjustment and establishment of a vital parts machining process.

还具体分析了模具的主要零部件(如凸凹模、卸料装置、拉深凸模、垫板、凸模固定板等)的设计与制造,冲压设备的选用,凸凹模间隙调整和编制一个重要零件的加工工艺过程。

The compression process CAD mainly included primary contents as following: compression part process judging, shaping force calculation, hydropress selection, opening die force and knockout press calculation, checking the worki...

模具结构CAD主要包括:总装设计、凸模设计、凹模设计、加料室的设计计算、凸模与加料室及凹模的配合形式、侧向抽芯机构设计、标准件的管理、非标准件的管理、工程图生成。

更多网络解释与凸模相关的网络解释 [注:此内容来源于网络,仅供参考]

counterpunch:反向凸模

cooling 冷却 | counterpunch 反向凸模 | cross section 截面

counterpunch:反凸模

manifolddie分歧管模具 | counterpunch反凸模 | modularmold组合式模具

counterpunch:反向凸模 冲孔机垫块

counterpulsationtherapy 反搏疗法 | counterpunch 反向凸模 冲孔机垫块 | counterpurchase 反购买 反向购买

male die:公模(凸模)

up stripper上脱料板 | male die公模(凸模) | feature die公母模

round punch:圆形凸模

round pole 圆形磁极 | round punch 圆形凸模 | round radius 圆角半径

up stripper:上脱料板 male die公模(凸模)

stripper pad脱料背板 | up stripper上脱料板 male die公模(凸模) | feature die公母模

peened head punch:镶入式冲头 锤击强化冲头 钻杆凸模

Pass Guide 穴型导板 | Peened Head Punch 镶入式冲头 锤击强化冲头 钻杆凸模 | Pilot Pin 定位销 导向销子

recessing punch:有槽凸模

recessed switch 暗线开关 | recessing punch 有槽凸模 | recessing tool 圆根切刀,圆根车刀,平面切刀,端面切刀,镗凸缘刀具,凹槽车刀

hot trephining:中孔凸模冲机

hot trepanning ==> 中空凸模冲孔 | hot trephining ==> 中孔凸模冲机 | hot trim ==> 热切边

holder of punch:凸模夹持器

hot work tool (die) steel 热作工具(模具)钢 | holder of punch 凸模夹持器 | die slide 下模滑动装置