- 更多网络例句与再啮合相关的网络例句 [注：此内容来源于网络，仅供参考]
-
This thesis discusses the following. First, we use the condition of inference and the concept of wildhabor cone to design the addendum circle. Second, we use TCA technique to obtain the relationship between the slip track and the angle of action, which then leads to the calculation of contact ratios. We can then design the tooth face width and the numbers of teeth based on contact ratios.
本文一开始先对空间渐开线齿轮之齿冠圆范围使用齿轮干涉条件与Phillips提出的Wildhabor Cone进行设定，再利用Litvin提出的齿面接触分析方法，得到空间渐开线齿轮对在啮合过程中作用角与滑动轨迹之间的关系，藉由此关系可以建立一套设计流程来调整齿面宽以及齿数等参数，使其能符合设计需求。
-
To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.
。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间的配合达到最佳状态，仍需大量的修整工作，如镗床的齿轮与齿条，若拆卸后齿轮的各项性能指标经检测尚能使用不需更换，而齿条磨损严重需更换，那么齿条及齿条安装面上的定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮的啮合间隙需达到技术要求的标准，此项工作需时约一天。
-
To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.
。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间旳配合达到最佳状态，仍需大量旳修整工作，如镗床旳齿轮与齿条，若拆卸后齿轮旳各项性能指标经检测尚能使用不需更换，而齿条磨损厉害需更换，那么齿条嘉逸条安装面上旳定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮旳啮合间隙需达到技术要求旳标准，此项工作需时约─天。
-
Once the end connector engages the O-ring seal, no more than 1/8 to 1/4 turn of the union nut will fully compress the O-ring in its groove.
一旦端口连接件啮合到O形环密封后，管接螺母再旋转的圈数不要超过1/8圈或1/4圈，这样就足以将O形环紧压在它的槽内。
- 更多网络解释与再啮合相关的网络解释 [注：此内容来源于网络，仅供参考]
-
re-engage：重新接入
re-emission 二次发射 二次辐射 | re-engage 重新接入 | re-engagement 再次接入 再次起动 再联锁 再啮合
-
re-engagement：再次接入 再次起动 再联锁 再啮合
re-engage 重新接入 | re-engagement 再次接入 再次起动 再联锁 再啮合 | re-engineering 再设计 重建