- 更多网络例句与内浇道相关的网络例句 [注：此内容来源于网络，仅供参考]
-
This paper describes the characteristics of the construction technique of floating plate ballast bed for subway at home and abroad and sums up the experience for the reference to the similar construction technique based on the construction technique of floating plate ballast bed with continuous-casting in place-metal elastic buffer in a double-tracked horseshoe-shaped tunnel of Shengzheng subway.
本文通过对深圳地铁一期工程单洞双线马蹄形隧道内，连续-现浇-金属弹簧隔振器式浮置板道床施工工艺的阐述，同时综合国内外地铁浮置板式道床施工工艺特点，总结了一些经验和认识，以供类似工程施工借鉴。
-
Keywords Aluminum Alloy;Die Castings;Numerical Simulation;Ingate;Process Optimization
铝合金；压铸件；数值模拟；内浇道；工艺优化
-
The production verifies that the desirable filling can be formed in the optimized ingate,which plays the uniform temperature distribution in the die and eliminates the cold shut in fi...
实际生产表明，改进后的内浇道形成了较理想的流态，使模具温度分布均匀，同时消除了铸件充型远端的冷隔缺陷。
-
It is proposed that the runner location should be first to be selected to ensure molten metal filling along the die wall in order to reduce melt flow resistance and then ingate should be located in the heavy section of the workpiece to which the melt would be filled at the beginning. As a result, the applied pressure could be transmitted fluently to avoid shrinkage cavity and to ensure castings quality.
指出浇道位置的选择首先要保证金属液沿着型壁顺序充填，以减少金属液的流动阻力；内浇道应使液态金属从制件厚壁处开始充填，以利压力的传递，消除缩孔，保证制件的质量。
-
The filling process was simulated to analyze local overheat in die resulting from irrational filling and cold shut occurred in far-end in aluminum alloy engine bracket.The results indicate that the defects are caused by irrational ingate design.
针对铝合金摩托车发动机支架在压铸生产中充型不合理导致模具局部温度过热以及铸件充型远端容易出现冷隔缺陷等问题，运用数值模拟方法对压铸工艺过程进行分析，发现内浇道结构不合理是导致以上问题的主要原因。
-
For defects including poor transparency,sticky pouring channel,blurs,bubble,bullion,flow mark,crack,poor dimension stability,internal stress and insufficient product physical strength,the cause of most of them is that the plastic is not fully dehumidified and dried.
透明度不佳，浇道粘住、毛边、气泡、银条、流痕、龟裂、尺寸安定性不佳、产生内应力、产品物性强度不足等缺点，其多数不良原因，在于成型前塑料末被充分除湿干燥所致。
-
The flow status of liquid metal in the sand box of group casting was discussed according to the fluid mechanics and heat transfer theory. Not only does the appearance of vying liquid metal happen when group casting between the big and small castings, identical castings in the multiple gates system appear too, even one casting.
运用流体力学、传热学原理，分析群铸时液态金属在各型腔内的流动情况，揭示出争铁液现象不仅在大小件混铸时发生，在多个内浇道浇注系统中群铸相同铸件，甚至仅一个铸件仍存在这一现象。
-
The ideal injection system formed in line density parts, and not effected by all the flow, the intake-side gate and the impact, relatively speaking , to Cold flow, if hot runner to achieve this, we must maintain the material in the hot runner in the molten state, not with the forming of sending.
理想的注塑系统形成密度一致的部件，不受所有的流道、飞边和浇口水口的影响。相对冷流道来讲，热流道要做到这一点，就必须维持材料在热流道内的熔融状态，不会随成形件送出。
-
For the casting characteristics of more complex shape, the two ingates were designed at the same time. The casting was divided into 4 positions to calculate the volume of the riser, and the chill was used in order to obtain the directional solidification sequence.
根据铸件形状较复杂的特点，设计了两个内浇道；将铸件划分为4个补缩区域进行补缩，并配合冷铁来实现铸件的顺序凝固。
-
The hammer handle with foam pattern of hammer-head is placed in the sand mold when molding.
造型时锤柄预先放置在砂型中，锤端和浇注系统内浇道的成型采用消失模。
- 更多网络解释与内浇道相关的网络解释 [注：此内容来源于网络，仅供参考]
-
sprue bushing：浇道衬套
(4) 喷嘴 喷嘴连接料筒和竖浇道衬套(sprue bushing).当料筒移到最前端的成形位置,其喷嘴外径必须包 覆在竖浇道定位环内,构成密封.喷嘴的温度应该设定在材料供货商建议之塑料熔化温度,或是略低 于温度.如此,清理料筒时,只要将料筒后退远离竖浇道,
-
infusorian：纤毛虫/纤毛虫的
infusoria /滴虫类/ | infusorian /纤毛虫/纤毛虫的/ | ingate /码头门/内浇道/内浇口/
-
parting line：合模線
UNDERCUT) 修模具去除倒角浇道凹弧(SPRUE BUSHING)与射嘴配合不正 重新调整其配合无浇道抓锁(SNATCHPIN) 加设抓锁合模线(PARTING LINE)或密封面(MATING SURFACE)不良 检修模具射入模内时产生焦斑(BURNING MARK) 降低注射压力及速度;
-
runner：流道
使用"流道"(runner) 对话框. ...基本概念 流道是指液压系统中流体在元件内流动的通路. 模具流道系统 普通的流道系统(RunnerSystem)也称作浇道系统或是浇注系统,是熔融塑料自射出机射嘴(Nozzle)到模穴的必经信道.
-
tightness test：密闭耐压系统
锰 Manganese | 密闭耐压系统 tightness test | N 内浇道 in-gate
-
ingather：收获/收入/收集
ingate /码头门/内浇道/内浇口/ | ingather /收获/收入/收集/ | ingathering /收获/收入/收集/