- 更多网络例句与内搭接相关的网络例句 [注：此内容来源于网络，仅供参考]
-
According to the elastic theory,this paper gives partition Law of stress and quantitative answers over the overlap joint weld on skirted support .
利用弹性理论，分析推证出了裙式支座搭接焊逢内的应力分布规律及其定量解答
-
The results show that the main cause of the angular distortion of the lap joint is the non-uniform distributed inherent shear strain component that is vertical to the weld line and exists in the plane paralleling to the weld line.
结果表明：搭接接头焊接角变形的产生主要是由焊缝及其附近区域与焊缝平行的平面内垂直于焊缝方向上不均匀分布的固有剪切应变分量引起的。
-
In this paper, a 4-node plate element combined with rivet element and contact element is employed to analyze two typical rivet joint structures, i.e., lap joint and butt joint. The penetration between two sub-plates in the lap zone or butt zone is avoided by introducing contact element in the proposed FE model. Bending deformation and its effect on in-plane displacement of the two typical rivet joint structures are studied.
本文采用四节点板单元，结合铆钉单元、接触单元，建立了针对铆接搭接及铆接对接两种典型结构的有限元模型，并考虑了搭接或对接区内的接触问题，通过参数分析研究了铆接搭接和对接结构在拉伸载荷下的弯曲效应及其对面内位移的影响。
-
Self-fluxing Fe-Cr-Ni-B-Si alloy prowders are laser clad on medium carbon steel substrate of dimensions 80×35×10mm〓. The investigation results of this clad layer are: micro-defects, micro-cavity and occluded forin substance, are the micro-cracks and crack resourses in clad layer; crack of coating propagates along the boundary of two kinds of eutectic sutructure; The included angle θ between the cracking direction and laser scanning direction in multitrack overlapping clad is smaller than that in one-track clad because of crack propagating along crystalline growth direction and crystalline direction in overlapping zone being different from it in one-track clad.
在调质态的45〓钢表面，采用预置粉末法进行FeCrNiBSi合金的多道搭接激光熔覆，对其熔覆层进行分析表明：多道搭接激光熔覆层裂纹扩展方向与激光扫描方向间的夹角θ与单道熔覆时相比明显变小，前者θ0°，后者θ角基本都为90°，这主要是因为多道搭接时，搭接区结晶方向发生了变化以及裂纹沿结晶方向扩展所致；激光熔覆层裂纹大多是以覆层与基材交界面的孔洞、熔覆层内不同方向共晶团间的显微缩孔、夹杂物的边界等三种显微缺陷作为裂纹源，并沿低熔点物相形成元素偏析造成弱化膜的共晶团界面扩展延伸。
- 更多网络解释与内搭接相关的网络解释 [注：此内容来源于网络，仅供参考]
-
Bore diameter：内径
Bond 粘接,连接,胶接,搭接,焊接 | Bore diameter内径 | Borescope 管道(探测)镜,内空(探测)镜
-
joule heating：焦耳热
高频感应加热机在光缆制造中的应用 [摘要]本文分析了高频感应加热原理,实践中的关键技术,以及在GYTS、GYTA53系列光缆中的应用优势. [关键词] 焦耳热(joule heating) 高频加热机(High-frequency machine) 钢带搭接 焦耳热 充满在毛细管内的的电解质在高电