允许偏差

词组短语

allowable deviation

与允许偏差相关的网络例句 [注：此内容来源于网络，仅供参考]

Allowable error of pipe center...

管口中心的允许偏差？

First, the overall satisfaction membership function of the group decision making is defined based on the allowable error given by the decision-maker respectively. Following that, a weight model is suggested for finding the maximal degree of the group preference satisfaction. Based on the suggested model, the consistency degree of the group preference is defined. Then, an alternation approach is proposed to improve the judgment of the low consistency degree of the decision-maker.

基于决策者给出的允许偏差，定义了群决策满意度隶属函数，建立了求解群体偏好满意程度最大化的权重模型，提出了群体偏好一致性程度的衡量指标，研究了对一致性程度较差的决策者判断进行交互调整的方法。

First, the uncertain ordered weighted averaging is used to aggregate the decision-maker's different preference information into the interval number comparison matrix. Then, the group's overall satisfaction membership function is defined based on the decision-making's allowable error. The maximal group consistency weight model is established.

采用UOWA算子将决策者的偏好信息集结为区间数互反判断矩阵和互补判断矩阵两种形式，结合决策者给出的允许偏差，定义群满意度隶属函数，建立求解群偏好一致程度最大化的权重模型。

An isolated point s statistic excluding method is proposed in this paper to eliminate crassitude error in clouding data, which include plenty of oddity data. The method based on the distance between two neighbour points can eliminate the data beyond normal distribution. A error limitation of angle and chordal highness method is used to filtrate clouding point.

针对大量含奇异点的数据点云，本文提出了剔除粗大误差的孤立点统计排异法，该方法根据对相邻点距离的统计，剔除在正态分布以外的点；对大量数据的精减，利用角度和弦高的最大允许偏差法进行点云精减。

Hot Rolled Half-round Steel and Half-oval Steel, Dimensions, Weights, Permissible Variations

棒钢材。热轧半圆钢和半椭圆钢。尺寸。重量。允许偏差

330 Allowable deviations of actual resulting linear density from nominal resulting linear density

实际测定的线密度与额定线密度的允许偏差

The test results showed its deviation was less than 0.0210%~0.031 7%, conforming to the State's permissible error.

测定结果表明，铝相对标准偏差小于0.020%～0.317%，测定结果符合国家标准允许偏差。

Standard of ornamental design acceptance of work: Ornamental design project is finishing dry hind, just can check and accept; Check and accept ornamental design project, whether does the breed that should check ornamental design, norms, design accord with design requirement; Ornamental design should be installed firm, its quality asks to reach tolerance, should accord with: The level of form ornamental design and perpendicular tolerance, every meters must not be more than 5 millimeter, must not be more than 3 millimeter endlong; The tolerance of position of alone ornamental design, must not be more than 10 millimeter; Ying Guangjie of ornamental design surface, design clarity, juncture rigor, must not interstitial, warp, edge damage drops the blemish such as horn; Back up spends exterior Ying Guangjie, design clarity, without break.

花饰工程验收标准：花饰工程完工并干燥后，方可验收；验收花饰工程，应检查花饰的品种、规格、图案是否符合设计要求；花饰应安装牢固，其质量要求及允许偏差，应符合：条形花饰的水平和垂直允许偏差，每米不得大于5毫米，全长不得大于3毫米；单独花饰位置的允许偏差，不得大于10毫米；花饰表面应光洁，图案清晰，接缝严密，不得有裂缝、翘曲、缺棱掉角等缺陷；裱花表面应光洁，图案清晰、无裂缝。

This international standard and GB 13432 — major changes compared to 1992 are as follows:—— the standard name is replaced by: labelingofprepack the labeling of foods for special dietary uses; lawk: GB 13432 — 1992 " Chapter 4 " and " the basic principles of Chapter 6 " merged to form the basic requirements of this standard of " Chapter 4 basic requirements ";--added allow nongraphite " energy and nutrient content claims "(see 5.4.1);--increase the allowed nongraphite " energy and nutrient content claims "(see 5.4.2);--increase the allowed nongraphite mutrients of " claimed "(see 5.4.3);--an increase of " food energy and nutrients of nongraphite, nongraphite values of expressions and tolerances for ".

本标准与GB 13432—1992相比主要变化如下：——标准的名称改为：预包装特殊膳食用食品标签通则；——将 GB 13432—1992&第4章基本原则&和&第6章基本要求&合并为本标准的&第4章基本要求&；——增加了允许标示&能量、营养素含量水平的声称&(见5.4.1)；——增加了允许标示&能量、营养素含量比较的声称&(见5.4.2)；——增加了允许标示&营养素作用的声称&(见5.4.3)；——增加了&食品中能量和营养素的标示方式，标示值的表述方式及允许偏差&。

The permissible deviation: verticality: it allows a standard deviation of no more than 1.5mm: two of the adjacent disk at the top permits a deviation no more than 2mm, the straddle disks at the top allows a deviation of no more than 5mm; disk face error: the adjacent disk permits a deviation no more than 1mm between the two edges, the straddle stets more than 5mm; indirect slit of the disks is no more than 2mm

允许偏差：垂直度：允许偏差不大于1.5mm 水平偏差：相邻两盘顶部允许偏差不大于2mm，成列盘顶部允许偏差不大于5mm ；盘面偏差：相邻两盘边不大于1mm ，成列盘面不大于5mm ；盘间接缝不大于2mm 。

与允许偏差相关的网络解释 [注：此内容来源于网络，仅供参考]

allowable variation：允许偏差

跳焊 skip welding | 允许偏差 allowable variation | 补强板 stiffening plate

allowable variation：允许偏差 容许变化

alkaline battery 碱性电池 | allowable variation 允许偏差 容许变化 | alternating current 交流电

capacitance：电容量

适用于高压旁路和耦合电路中.其中的低损耗高压圆片瓷介电容器具有较低的介质损耗,特别适合在电视接收机的行扫描等电路中使用. 2.技术指标(SPECIFICATIONS) 电容量(capacitance) 18pF~33000pF 电容量允许偏差(capacitance tolerance) K(±10%),M(±2

deviant behavior：偏差行为

换言之,社会问题就象偏差行为(deviant behavior)一样,是由于文化上认同的目标同达成目标所使用的手段之间存有差距的结果. 例如,在现代社会人追求事业上的成功以获取较高经济收入和社会地位,这是在文化规范上得到允许的目标,

drainpipe branch：排水管支管

允许偏差 allowable variation | 排水管支管 drainpipe branch | 儒胀测点 creep measuring points

neat：整齐

允许偏差allowable deviation | 整齐neat | 整体吊装be hoisted integrally

permissible value：允许值

permissible tolerance 容许公差 | permissible value 允许值 | permissible variation 允许偏差

permit precinct：(工程的)允许范围内/允许区域内

745,"permissible deviation "," (工程的)容许偏差" | 746,"permit precinct"," (工程的)允许范围内/允许区域内" | 747,"permit to work "," (工程的)允许施工/容许实施"

Tolerances：允许偏差

2.5 Loading Conditions and Strength Calculation 负荷条件及强度计算 | 2.6 Tolerances 允许偏差 | 3. DETAIL DESIGN 详细设计

pre-established allowable deviation：预定允许偏差

pre-equilibrated aqueous phase 预平衡水相 | pre-established allowable deviation 预定允许偏差 | pre-evaporation 初步蒸发