- 更多网络例句与侧立柱相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Methods］When scoliosis of patients were corrected to a certain degree after three weeks of halo pelvic distraction, the most serious collapsed ribs of concave side of the curve underwent a transverse incision the cross ribs. A special rib bender was used to bend the exposed 3 to 6 ribs. The bent ribs were pulled up by double-stranded 10# thick silk which was extended out through the skin and fixed in the upright post of the instrument of Halo pelvic distraction with rubber membranes.
方法］颅盆牵引3周后，脊柱侧弯矫正到一定程度时，在侧弯凹侧肋骨塌陷最重的部位，与肋骨交叉作横切口，暴露3～6条肋骨，用特制的肋骨折弯器将肋骨折弯变圆，用10号双股粗丝线将每条肋骨提起，自皮肤穿出通过橡皮膜在颅盆装置的立柱上作牵引。
-
［Objective］To sum up the experience of wearing the halo pelvic and level traction costoplasty to treat 35 cases of severe scoliosis combined with collapsed chest.［Methods］When scoliosis of patients were corrected to a certain degree after three weeks of halo pelvic distraction, the most serious collapsed ribs of concave side of the curve underwent a transverse incision the cross ribs. A special rib bender was used to bend the exposed 3 to 6 ribs. The bent ribs were pulled up by double-stranded 10# thick silk which was extended out through the skin and fixed in the upright post of the instrument of Halo pelvic distraction with rubber membranes.［Results］Thirty-three in 35 patients underwent costoplasty.
［目的］介绍35例重度脊柱侧弯合并严重胸廓塌陷的病例，在颅盆牵引的过程中，同时采用肋骨成形术加水平牵引治疗胸廓塌陷［方法］颅盆牵引3周后，脊柱侧弯矫正到定程度时，在侧弯凹侧肋骨塌陷最重的部位，与肋骨交叉作横切口，暴露3～6条肋骨，用特制的肋骨折弯器将肋骨折弯变圆，用10号双股粗丝线将每条肋骨提起，自皮肤穿出通过橡皮膜在颅盆装置的立柱上作牵引。
-
Bus passengers in the car to stand at attention to the vision of design, as far as possible to increase the span and the side-column height.
公交车注意车内乘客站立时的视野设计，尽量加大侧窗立柱的跨度和高度。
-
The second step is to calculate the frame design. Which includes the frame quality, the flexure style, the crooked intensity. When designing the car body, the first is the structural design of car body. Then is the design and calculate the box column, the selection of the car body, the design of cat ladder, the selection of the car door and the design of the car above floor.
根据弯曲强度，扭转应力的要求，进行了车架的设计计算；在侧围设计中，对立柱进行了研究，根据同行比较选定了侧围板，及爬梯的结构，选择了车门和进行了顶蓬的设计。
-
The heat treatment technology of the column wear plate s of Zhuan 8A bogie frames is described, and the effects of two different heat treatment technologies on the wear plate structure are analyzed.
论述了转8A型转向架侧架立柱磨耗板的热处理工艺，分析了2种不同热处理工艺对磨耗板组织的影响。
-
Based on pole model of lathe, thickness of side-board is treated as design parameter. This problem becomes a nonlinear problem, but it may become a linear problem using method of differential coefficient. Through method of calculating energy of sub-structure, thinking of each board separately, so getting final results rapidly.
以机床立柱模型为例，将模型的侧板板厚作为设计参数，并运用微分近似的方法，将非线性问题简化为线性问题求解，推导出了适用于板结构设计的计算公式，并通过计算子结构能量的方法，将每块侧板分开来考虑，降低了对计算机处理能力的要求，从而快速得到最终结果。
-
B. Front boom of gantry is equipped with two horizontal traveling carriages, each carriage is hold slide/lifting lifting column, the traveling range between two carriages is 300 – 2500 mm.
门型架前侧装有两组横移滑动台车，每座台车有直立柱升降及滑动系统，两座横移滑动台车间距为500 – 2500 mm，横移台车由马达驱动沿著尺牌移动。
- 更多网络解释与侧立柱相关的网络解释 [注：此内容来源于网络，仅供参考]
-
heelpost：侧立柱 闸门侧立柱 承重柱 门轴柱
heelplateseat 背靠块座 侧支承块底座 | heelpost 侧立柱 闸门侧立柱 承重柱 门轴柱 | heelpost 柱脚
-
heelpost：柱脚
heelpost 侧立柱 闸门侧立柱 承重柱 门轴柱 | heelpost 柱脚 | heelpost 船尾柱
-
jamb stone：门窗边框石,石门窗侧壁
jamb shaft 门窗立柱 | jamb stone 门窗边框石,石门窗侧壁 | jamb wall 侧壁
-
jambstone：门窗边框石 石门窗侧壁
jambshaft 门窗立柱 | jambstone 门窗边框石 石门窗侧壁 | jambwall 侧壁
-
Back side panel：后侧板
Back panel||后围板 | Back side panel||后侧板 | Back wall pillar||后围立柱
-
jamb shaft：门窗立柱
jamb post ==> 门边框柱,门窗侧柱,石门窗侧壁 | jamb shaft ==> 门窗立柱 | jamb stone ==> 门窗边框石,石门窗侧壁
-
side wall frame：侧围立柱
power-assisted brace gas spring 侧围 %2:[GaH7 | side wall frame 侧围立柱 2kH"_}|}"~ | side wall pillar 侧窗立柱 #IB[H^jXb