- 更多网络例句与产生裂纹相关的网络例句 [注：此内容来源于网络，仅供参考]
-
It is the unsetting fireproof material composed of powder fireproof materials and agglutinant for the use of mixing mud.
主要以粉状耐火物料和结合剂组成的供调制泥浆用的不定形耐火材料，使用过程中不产生裂纹。
-
Crack propagation leading to decohesion or delamination is one of the major failure.
但在生产与使用过程中膜基界面处容易产生裂纹，裂纹的扩展导致膜层的脱落是使膜层完全失效的主要形式之一。
-
Some meaningful conclusions had been made: 1. In the test, a form of subsurface crack is relative to the sclerometer's shape, when the top of the sclerometer is sharper the crack is easier form.
在该划痕试验中，亚表面裂纹与压头本身的形状有关；当压头顶部较尖锐时，在划痕深度一定的条件下，更容易产生裂纹； 2。
-
It is necessary to analyze the reasons that cause straint stress so as to prevent the weld from crack.
要防止产生裂纹，就要从仔细分析焊接时拘束应力产生的条件出发，达到防止产裂纹的目的。
-
The oxidation-deoxidization between Al and ZrO2 or Y2O3 is one of the mechanisms of high temperature oxidation failure of TBCs. The failure under thermal shock results from the formation of cracks normal to the bond/top coat interface, due to the different coefficients of thermal expansion between bond coat and top coat and the temperature change.
底层与面层之间界面存在的部分Zro，或YZO3被A1还原生成Zr或Y，A1被氧化形成A1203的反应是热障涂层高温氧化失效的原因之一；热震失效的主要原因是由于底层与面层之间热膨胀系数的差异而产生的剪应力与喷涂时产生的内应力之和导致面层产生裂纹。
-
In the paper,the cause and treatment technology for the connection welding seam crackle defects of the bucket sharft flange and bucket sharft of the coal yard bucket stacker/reclaimer of a 660 MW thermal power plant are introduced.
针对某火力发电厂660MW机组燃料煤场斗轮堆取料机的斗轮轴法兰与斗轮轴连接焊缝裂纹缺陷，对产生裂纹的原因及处理工艺进行了分析和论述，制定了处理措施及焊接工艺。
-
A summary of study advance at domestics and abroad on rice fissure was introduced and the mechanism of fissureformation was also discussed in the paper.
本文对国内外有关稻谷裂纹的研究进展作了较为详细的综述并分析了稻谷产生裂纹的内在机理。
-
Scanning electron microscope analysis showed that there are more elements enrichments in the crack position, which are O, Ca, Mg, Na and Cu etc. The carbon content of molten, casting process, heating time and so on are main reasons which result in the cracks.
扫描电镜分析表明，高强钢裂纹处存在较多的O、Ca、Mg、Na、Cu等元素，钢水碳含量、连铸工序、加热时间等是高强钢产生裂纹的主要原因。
-
The experimental result shows that when the discharge time was more than 1.5μs, small crack emerged in the fuses due to mechanical force on the heated fuse, and the metallized layer would be evaporated as the crack became long enough to generate disruptive discharge. When the discharge time was less than 150ns, small crack emerged in the fuses due to the current heat, and the metallized layer would be evaporated as the crack became long enough to generate disruptive discharge.
实验结果表明：当熔丝的通流时间大于1.5 ms时，电流热效应产生的机械力使安全膜熔丝的金属层产生微小裂纹，当裂纹达到一定长度，两端发生击穿放电，金属层因蒸发而断开；当熔丝中通过较大的电流时，短时间内(50 ns)的电流热效应使熔丝金属层发生熔化产生裂纹，裂纹两端发生击穿放电，金属层因蒸发而断开。
-
However, such defect as crack, pore, oxidation and ill bonding between cladding layers might appear in RLF parts if the process parameters controlled improperly. And crack was a kind of defect, which was the most familiar and companied with the largest brisance.
但是，如果成形条件控制不当，易于在成形件中产生裂纹、气孔、夹杂、层间结合不良等缺陷，而裂纹是成形过程中最常见、破坏性最大的一种缺陷。
- 更多网络解释与产生裂纹相关的网络解释 [注：此内容来源于网络，仅供参考]
-
checking：裂纹
偶氮染料(Azo dyestuff)颜料,结果在油漆担体 (vehicle ) 和溶剂,通常应用在涂料工业中的,会有渗出双偶氮染料(disazo dyestuff)的分子大小有很大的增加时,和大部单偶氮染产生白垩(chalking)、裂纹(checking)和裂开(crackirg)的情形.
-
cracking：破裂
文档简介: 4-13 开模时或顶出时成品破裂 破裂(cracking)是成形品表面产生毛发状之裂纹,成形品会有棱角时,此部份常发生不易看出的细裂纹.裂纹是成形品的致命不良现象主要原因如下所示.
-
flow mark：流痕
4-13 开模时或顶出时成品破裂 破裂(cracking)是成形品表面产生毛发状之裂纹,成形品会有棱角时,此部份常发生不易看出的细裂纹.裂纹是成形品的致命不良现象主要原因如下所示....4-12 流纹 流痕(flow mark)是熔融材料流动的痕迹,
-
Crackles like a real fire：裂纹像一个真正的火警
Generates 3,000 BTUs of heat产生3000 btus热 | Crackles like a real fire裂纹像一个真正的火警 | Other Matching Items sold Seperately.其他符合条件的物品,单独出售.