wrist joints

wrist joints的基本解释

-

[医] 腕关节

与wrist joints相关的网络例句 [注：此内容来源于网络，仅供参考]

The current research points out that for the CFCHS joints the linear extrapolation method can be used for chords,whereas the quadratic extrapolation method must be used for braces.The hot spot stress distributions on the CFCHS joints tend to be more uniform and their SCFs become smaller significantly,compared with the CHS joints.Axial tension on the brace puts the CFCHS joints at a disadvantage,which produces higher SCFs than axial compression.The effects of nondimensional geometric parameters β,τ and γ on SCFs of the chords of the CFCHS joints are basically the same as those of the CHS joints,but for the braces,there is a bit difference in the effects of parameters β,τ and γ between the two kinds of joints.Concrete has the function of improving the CFCHS joint rigidity and then decreasing SCFs which is expected to increase fatigue strength,but concrete strength grade does not exert significant influence on SCFs.

研究表明：CFCHS节点的热点应力，对主管可采用线性外推方法，对支管需采用二次外推方法；相比CHS节点，CFCHS节点的热点应力分布趋于均匀，SCF显著减小；CFCHS节点支管轴向受拉比受压不利，SCF增大；CFCHS节点几何参数β，τ，γ对主管SCF的影响效应与CHS节点基本一致，但是对支管SCF的影响效应与CHS节点有些差异；混凝土的作用主要是改善CFCHS节点刚度，从而降低SCF，并预期可提高疲劳强度，但混凝土自身强度等级的高低没有显著影响节点的SCF。

In the experimental study, 12 joints tests are completed, including 5 uniplanar X joints loaded with axial forces, 3 uniplanar X joints loaded with in-plane bending, 4 multiplanar XX-joints loaded with axial forces, with the emphasis on the influence of β and the existence of the out-of-plane braces, of which the multiplanar XX-joints tests is the first experiment project in china.

试验重点研究节点支主管宽度比β以及平面外支管荷载等因素对节点性能的影响，共进行了3个足尺方管平面X型受压节点，3个足尺方管平面X型受弯节点、2个方、圆管杂交平面X型受压节点和4个足尺方管空间XX型节点试验，其中方管空间XX型相贯节点试验是国内的首次试验。

4 Results of nondestructive test for weld joints shall be graded according to JB 4730. Following requirements shall be met: a For radial test, quality grade of radial transillumination can't be lower than Grade AB, and that of weld joints shall meet table 10; b For supersonic test, approval standard for weld joints are as follows: 1 For weld joints of 100% supersonic test, grade Ⅰ. 2 For weld joints of local supersonic test, grade Ⅱ. c For magnetic particle test and penetration test, grade Ⅰ.

7.5.4 管道焊接接头的无损检测应按 JB 4730 进行焊缝缺陷等级评定，并符合下列要求： a 射线检测时，射线透照质量等级不得低于 AB 级，焊接接头经射线检测后的合格等级应符合表 10 的规定； b 超声波检测时，管道焊接接头经检测后的合格标准如下： 1 规定进行 100%超声波检测的焊接接头 I 级合格； 2 局部进行超声波检测的焊接接头 II 级合格； c 磁粉检测和渗透检测的焊接接头 I 级合格。

与wrist joints相关的网络解释 [注：此内容来源于网络，仅供参考]

Male connector for butt joints--Assembly：卡套式锥螺纹对接直通管接头

卡套式端对接直通接头体 Straight thread connector for butt joints--... | 卡套式锥螺纹对接直通管接头 Male connector for butt joints--Assembly | 卡套式锥螺纹对接直通接头体 Male connector for butt joints--...

Male connector for butt joints--Body：卡套式锥螺纹对接直通接头体

卡套式锥螺纹对接直通管接头 Male connector for butt joints--Assembly | 卡套式锥螺纹对接直通接头体 Male connector for butt joints--Body | 卡套式对接直通管接头 Union for butt joints--Assembly

Interphalangeal joints of hand：指骨间关节

Metacarpophalangeal joints 掌指关节 | Interphalangeal joints of hand 指骨间关节 | Joints of pelvic girdle 下肢带连结