weld seam

weld seam的基本解释

-

焊缝

与weld seam相关的网络例句 [注：此内容来源于网络，仅供参考]

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

The series of computerized automatic welder for portal ring seam is applicable for both of wire-drive and butt-weld ring seams at M direction for various casket cylindrical metal materials with plate thickness of 0.8mm~2.5mm and lmm8mm, due to silver or golden welding seam, beautiful and clear appearance, high strength, continuous and stepless weld-speed regulating and non corrosion in crystalline, this equipment is mainly suitable for ring-seam butt-weld to SS compressing components and various inners concerning solar water heater, enamel water container, electric heater and turkey boiler, and for ring-seam wire-drive and butt-weld to barrel and tank for large industry production.

该系列龙门式环缝电脑自动焊接设备可对板厚0.8mm—2.5mm和1mm—8mm的各种圆桶形金属件实施M向位置的环缝对接和送丝焊接，为两用型设备。焊缝颜色呈银白色或金黄色，焊接美观光洁、强度高、无晶间腐蚀，焊接速度连续无级可调，主要适用于不锈钢承压或太阳能热水器内胆、搪瓷水箱内胆、电热水器内胆、火鸡锅和对大型工业制桶、罐等产品的环缝对接、送丝焊接。

In addition, effects of weld heat input on microstructure and performance of the weldjoints are analyzed. The test results indicate that by controlling weld heat input about 16kJ/cm and practicingmulti-layer weld process, the coarse austenitic grains in the weld metal and lumpish ferrite in the heat affectedzone can be avoided so that the microstructure and performance of the weld joints can be ensured.

结果表明，采用多道焊焊接工艺，严格控制焊接线能量在16 kJ/cm左右，可以防止T91钢焊缝区奥氏体晶粒粗大，避免在热影响区出现块状铁素体组织，从而保证焊接接头区具有良好的组织性能。

与weld seam相关的网络解释 [注：此内容来源于网络，仅供参考]

OVERSEAM ：包缝

暗边缝-----HIND EDGE SEAM | 包缝------OVERSEAM ,CLOSED SEAM ,OVEREDGE SEAM ,OVERCAST SEAM ,OVERLOCK SEAM | 明包缝-----FLAT FELL SEAM

OVERSEAM ,CLOSED SEAM ,OVEREDGE SEAM ,OVERCAST SEAM ,OVERLOCK SEAM：包缝

暗边缝-----HIND EDGE SEAM | 包缝------OVERSEAM ,CLOSED SEAM ,OVEREDGE SEAM ,OVERCAST SEAM ,OVERLOCK SEAM | 明包缝-----FLAT FELL SEAM

OVEREDGE SEAM ：包缝

暗边缝-----HIND EDGE SEAM | 包缝------OVERSEAM ,CLOSED SEAM ,OVEREDGE SEAM ,OVERCAST SEAM ,OVERLOCK SEAM | 明包缝-----FLAT FELL SEAM