weld [weld]

weld的基本解释

vt.

焊接, 使密接, 使结合, 使成整体

• We were welded into a fighting collective.
• 我们结成一个战斗集体。

• He welded the broken rod.
• 他焊接一根断了的杆子。

• It takes speed and skill to weld steel at this heat.
• 在这样的温度焊钢需要速度和技术。

vi.

焊牢

n.

焊接, 焊接处, 焊缝

weld的同义词

v. unite · cement · solder · bind · join

与weld相关的网络例句 [注：此内容来源于网络，仅供参考]

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

In addition, effects of weld heat input on microstructure and performance of the weldjoints are analyzed. The test results indicate that by controlling weld heat input about 16kJ/cm and practicingmulti-layer weld process, the coarse austenitic grains in the weld metal and lumpish ferrite in the heat affectedzone can be avoided so that the microstructure and performance of the weld joints can be ensured.

结果表明，采用多道焊焊接工艺，严格控制焊接线能量在16 kJ/cm左右，可以防止T91钢焊缝区奥氏体晶粒粗大，避免在热影响区出现块状铁素体组织，从而保证焊接接头区具有良好的组织性能。

Stract : The synopsis introduced robot to weld the technique development process, design of weld a small car, and the welder equip the design for have, welding a small car to adopt part to have already have of product, carried on a design towards welding small garage to walk organization, weld the small car will pack Be welding an operation on board, follow behind to weld operation machine of action to carry out to weld relatedly.

摘 要：简要介绍了机器人焊接技术发展历程，设计的焊接小车，及焊接工装设备的设计，焊接小车采用了部分已有的产品，对焊接小车行走机构进行了设计，焊接小车将装在焊接操作机上，跟随焊接操作机的动作来实现相关的焊接。

与weld相关的网络解释 [注：此内容来源于网络，仅供参考]

weld：焊接

单击"工具"(Tools)>"焊接"(Weld)>"焊条"(Rod). "焊条"(WELDING ROD) 对话框打开. 从"焊条列表"(Rod List) 中选取焊条名称并按照下列步骤操作:如果是指定,则活动组件中已取消指定的焊条会列在"找到的项目"(items found) 列表中.

weld：焊缝

单击"编辑"(Edit)>"焊缝"(Weld)>"转换"(Convert). "焊缝转换"(Weld Conversion) 对话框打开. 在"转换到"(Convert To) 下,选取要执行的几何转换类型:如果组件中不含有实焊缝特征,则"转换到"(Convert To) 的缺省设置将是"轻焊"(Light).

weld：焊

压模 stamping | 焊 weld | 拉床 broaching machine

weld：接合 接合

Weight 权值 权值 | weld 接合 接合 | What's new 新特性 新增功能

circumferential weld：环缝

局部变形 local distortion | 环缝 circumferential weld | 顶板 top plate