wedge gearing

与wedge gearing相关的网络例句 [注：此内容来源于网络，仅供参考]

In view of product quality of cross wedge rolling semifinished product of automotive power-shift box middle shaft which has heavy sectional shrinkage, numerical simulation and experimental method were adopted to analyze single wedge rolling and second wedge rolling method. It is found out that contrast second wedge rolling, single wedge rolling will not make workpiece bend easily, and after rolling the workpiece has no neck shrinkage.

针对用楔横轧工艺生产具有大断面收缩率特点的汽车变速箱中间轴毛坯所存在的产品质量问题，利用数值模拟与实轧试验对汽车变速箱中间轴毛坯一次楔成形和二次楔成形进行了分析研究，发现采用一次楔成形方法加工汽车变速箱中间轴毛坯，轧件不易发生弯曲，中间断面收缩率最大处没有发生缩颈现象，心部质量也较二次楔成形好。

The tongs all passes in the machine the gearing on the bed what tongs the gearing on realizes with superficial contact in the cowgirl on the bed in machine or matches.when the tongs installs in the machine bed work on the stage,the center of gravity of the tongs should be as far as possible low,center of gravity the more high an accepts should the dint is more big,the tongs bottom four directions should bulge,make its contact good,or the bottom establishes four a feets.when the tongs installs on the machine bed principal axis,the tongs install the to should have the enough match accuracy with principal axis cowgirl surface,and guarantee the gearing the stability dependable.

夹具体在机床上的安装都是通过夹具体上的安装基面与机床上的相应表面的接触或配合实现的。当物流设备需要的公司体在机床工作台上安装时，夹具的服装厂应尽量低，重心越高则支承面应力越大，夹具底面四边应凸出，使其接触良好，或底部设置四个支脚。当夹具体在机床主轴上安装时，夹具安装基面与主轴相应表面应有足够的配合精度，并保证安装稳定可靠。

In this dissertation, first, based on theory of cutting tooth about the gleason spiral bevel gear, the equation of meshing in the process of cutting tooth, the surface equation of generating gear as well as the general tooth surface equation of the double circular arc spiral bevel gear, using GB12759-1991 type of double circular arc gear as a basic gear profile, a three-dimension solid model of double circular arc spiral bevel gear which has the good adaptability was carried out by used of Unigraphics software;Second, by researching of the algorithm about contact and collision as well as various contact types based upon Contacting Finite Element Method, a foundation was laid for selecting the contact type in analyzing contact stress of double circular arc spiral bevel gearing;Finally, through the connection port of PARASOLID between UG software and ANSYS/LS-DYNA software, the three-dimension solid model of double circular arc spiral bevel gearing obtained above in UG was imported into ANSYS/LS-DYNA, a finite element analyzing about contact stress of double circular arc spiral bevel gearing was carried out by applying new loading method.

本文首先基于格利森弧齿锥齿轮加工原理及切齿啮合过程中的啮合方程、产形轮齿面方程以及双圆弧弧齿锥齿轮的齿面方程，选用GB12759-1991型双圆弧齿轮基本齿廓为基准齿形，利用Unigraphics软件的建模功能，绘制了有较好适应性的双圆弧弧齿锥齿轮传动三维实体模型。其次，描述了应用有限单元法进行实体接触与碰撞问题算法的公式，研究了有限元分析中的各种接触类型以及双圆弧弧齿锥齿轮接触应力分析中所选择接触类型的依据。最后，通过UG软件和ANSYS/LS-DYNA之间的PARASOLID接口工具包，将UG软件中得到的啮合齿轮模型导入ANSYS/LS-DYNA有限元分析软件，给出一种新的加载方法，进行了双圆弧弧齿锥齿轮传动的接触应力的有限元分析。

与wedge gearing相关的网络解释 [注：此内容来源于网络，仅供参考]

wedge friction gearing：楔形轮摩擦传动

wedge formation ==> 楔式队形=>ウェッジフォーメーション | wedge friction gearing ==> 楔形轮摩擦传动 | wedge friction wheel ==> 楔形摩擦轮