ultimate tensile strength

ultimate tensile strength的基本解释

-

极限抗张强度

与ultimate tensile strength相关的网络例句 [注：此内容来源于网络，仅供参考]

The results show that proper RRA heat treatment can improve SCC properties with retention of the high strength of T6 level. After preaging at 100℃for 24 h, retrogression at 200℃for 7 min, and reaging at 100℃for 24 h, the ultimate tensile strength, yield strength and elongation of the alloy are 795 MPa, 767 MPa and 9.1%, respectively. Meanwhile the failure time of the alloy applied to tensile strength of 210MPa in 3.0%NaCl+0.5%H2O2corrosion condition is longer than 720 h. The corresponding TEM observation shows that after retrogression for 7 min and re-aging treatment, the microstructure of grain boundary is similar to that treated in the T73 condition with coarsen and isolated distribution, and the microstructure inside grain is similar to that treated in the T6 condition with small and homogeneous distribution.

研究结果表明：在峰值时效T6状态下合金强度高，但抗应力腐蚀性能差；采用合适的RRA热处理工艺既能使合金保持T6状态下的高强度的同时，又能显著改善合金的抗应力腐蚀性能；经回归7 min RRA处理后合金的晶界类似T73态析出相聚集粗化，而晶内类似T6态析出相细小弥散分布，在拉伸应力为210 MPa和3.0%NaCl+0.5%H2O2腐蚀液中，其断裂时间大于720 h，相应的抗拉强度、屈服强度和延伸率分别为795 MPa， 767 MPa和9.1%，显示优越的综合性能。

The results show that proper RRA heat treatment can improve SCC properties with retention of the high strength of T6 level. After pre-aging at 100 ℃ for 24 h, retrogression at 200 ℃ for 7 min, and reaging at 100 ℃ for 24 h, the ultimate tensile strength, yield strength and elongation of the alloy are 795 MPa, 767 MPa and 9.1%, respectively. Meanwhile the failure time of the alloy applied to tensile strength of 210 MPa in 3.0%NaCl+0.5%H2O2 corrosion condition is longer than 720 h. The corresponding TEM observation shows that after retrogression for 7 min and re-aging treatment, the microstructure of grain boundary is similar to that treated in the T73 condition with coarsen and isolated distribution, and the microstructure inside grain is similar to that treated in the T6 condition with small and homogeneous distribution.

研究结果表明：在峰值时效T6状态下合金强度高，但抗应力腐蚀性能差；采用合适的RRA热处理工艺既能使合金保持T6状态下的高强度的同时，又能显著改善合金的抗应力腐蚀性能；经回归7 min RRA处理后合金的晶界类似T73态析出相聚集粗化，而晶内类似T6态析出相细小弥散分布，在拉伸应力为210 MPa和3.0%NaCl+0.5%H2O2腐蚀液中，其断裂时间大于720 h，相应的抗拉强度、屈服强度和延伸率分别为795 MPa， 767 MPa和9.1%，显示优越的综合性能。

The results show that proper RRA heat treatment can improve SCC properties with retention of the high strength of T6 level. After pre-aging at 100℃ for 24 h, retrogression at 200℃ for 7 min, and reaging at 100℃ for 24 h, the ultimate tensile strength, yield strength and elongation of the alloy are 795 MPa, 767 MPa and 9.1%, respectively. Meanwhile the failure time of the alloy applied to tensile strength of 210 MPa in 3.0%NaCl+0.5% H2O2 corrosion condition is longer than 720 h. The corresponding TEM observation shows that after retrogression for 7 min and re-aging treatment, the micro- structure of grain boundary is similar to that treated in the T73 condition with coarsen and isolated distribution, and the microstructure inside grain is similar to that treated in the T6 condition with small and homogeneous distribution.

研究结果表明：在峰值时效T6状态下合金强度高，但抗应力腐蚀性能差；采用合适的RRA热处理工艺既能使合金保持T6状态下的高强度的同时，又能显著改善合金的抗应力腐蚀性能；经回归7min RRA处理后合金的晶界类似T73态析出相聚集粗化，而晶内类似T6态析出相细小弥散分布，在拉伸应力为210 MPa和3.0%NaCl+0.5%H2O2腐蚀液中，其断裂时间大于720h，相应的抗拉强度、屈服强度和延伸率分别为795 MPa，767 MPa和9.1%，显示优越的综合性能。

与ultimate tensile strength相关的网络解释 [注：此内容来源于网络，仅供参考]

ultimate tensile strength：极限抗拉强度

螺丝因应不同的钢材有特定的抗拉强度(tensile strength),虽然螺丝在接近极限抗拉强度(ultimate tensile strength)时仍然不会断裂,但若再加上振动力或动力荷载后,螺丝就会变得较容易折断了

ultimate tensile strength：抗拉强度

螺丝因应不同的钢材有特定的抗拉强度(tensile strength),虽然螺丝在接近极限抗拉强度(ultimate tensile strength)时仍然不会断裂,但若再加上振动力或动力荷载后,螺丝就会变得较容易折断了

ultimate tensile strength：极限抗拉应力

ultimate stress 极限应力 | ultimate tensile strength 极限抗拉应力 | ultra high strength concrete 超高强度混凝土