two address instruction

two address instruction的基本解释

-

二地址指令

与two address instruction相关的网络例句 [注：此内容来源于网络，仅供参考]

ACALL is a two- byte instruction , and is limited to a 2K address block.

ACALL是两个位元组的指令，并仅限于2K的地址块。

Pinout: C High-performance 32-bit RISC Architecture C High-density 16-bit Instruction Set C Leader in MIPS/Watt C Little-endian C Embedded ICE (In-circuit Emulation) 8-, 16- and 32-bit Read and Write Support 256K Bytes of On-chip SRAM C 32-bit Data Bus C Single-clock Cycle Access Fully Programmable External Bus Interface C Maximum External Address Space of 64M Bytes C Up to Eight Chip Selects C Software Programmable 8/16-bit External Data Bus Eight-level Priority, Individually Maskable, Vectored Interrupt Controller C Four External Interrupts, including a High-priority, Low-latency Interrupt Request 32 Programmable I/O Lines Three-channel 16-bit Timer/Counter C Three External Clock Inputs C Two Multi-purpose I/O Pins per Channel Two USARTs C Two Dedicated Peripheral Data Controller Channels per USART Programmable Watchdog Timer Advanced Power-saving Features C CPU and Peripheral Can be Deactivated Individually Fully Static Operation: C 0 Hz to 75 MHz Internal Frequency Range at VDDCORE = 1.8V, 85C 2.7V to 3.6V I/O Operating Range 1.65V to 1.95V Core Operating Range -40C to +85C Temperature Range Available in 100-lead TQFP Package

M5L8253P-5引脚说明： C型高性能32位RISC架构C高密度以MIPS /瓦C小端C十六位指令集C领袖嵌入式冰8 - 16 -位和32位的读写支持256K的片上SRAM的 32位数据总线C单时钟周期存取字节完全可编程的外部总线接口C最大的外部地址空间的64M字节多达8个C芯片选择C软件可编程8位外部数据总线8级优先级，独立可屏蔽，向量中断控制器C四外部中断，其中包括一个高优先级，低延迟中断要求32个可编程I / O口线三通道16位定时器/计数器C三个外部时钟输入C两多用途I / O引脚每通道2个通用同步C两专用外设数据控制器通道每个USART可编程看门狗定时器先进的节能特性 CPU和外设可停用独立全静态工作中：C 0 Hz至75 MHz的频率范围内的VDDCORE = 1.8，85℃2.7V到3.6VI / O的操作1.65V到1.95V范围核心工作电压范围在- 40C至+85 C温度范围内使用的100引脚TQFP封装

与two address instruction相关的网络解释 [注：此内容来源于网络，仅供参考]

two address instruction：二地址指令

twisting joint 绞接 | two address instruction 二地址指令 | two dimensional copying system 二维仿形

two address instruction：两地址指令

two-address computer 双地址计算机 | two-address instruction 两地址指令 | two-arm caliper 双臂井径仪

two address instruction：双址指令

"镊取","tweezer grasp" | "双址指令","two address instruction" | "双料架系统","two bin system"

two address instruction：二址指令

二址码 two-address code | 二址指令 two-address instruction | 二址指令系统 two-address instruction system