torsion lever

torsion lever的基本解释

-

扭杆

与torsion lever相关的网络例句 [注：此内容来源于网络，仅供参考]

The static model of torsion joint is based on that of bending joint. The effects of structure parameters inside air pressure, initial angle, rube average radius, rube shell thickness on the turning angle are analyzed and the following conclusions are drawn: the relationship between the angle of torsion joint and the inside air pressure is basically linear, the angle of torsion joint increases with the initial angle and rube average radius, the angle of torsion joint decreases while the rube shell thickness increases. The kinetic equation is built for torsion joint. Simulating experiment implies that the time of inflating and deflating process is extremely shorter than that of kinetic process. So the pneumatic process can be ignored in actual system design and control. The factors that affect the dynamic features of torsion joint, such as shell thickness of rubber tube, average radius, initial angle, connector's outlet area, moment of inertia and viscous damping coefficient, are analyzed and the following conclusions are drawn: the change of rube shell thickness has no effects on the dynamic process of FPA inside air pressure while greatly affects the turning angle of torsion joint; when the rube shell thickness is small, the torsion joint has a bigger turning angle, no overshoot and long risetime, when the shell thickness is big, the turning angle of torsion joint is small, but has high response speed, overshoot and low shock; when the rube average radius increases, the turning angle of torsion joint increases and the overshoot increases too; when the initial angle of torsion joint is big, the turning joint is big, the overshoot is small and shock is low, but the risetime is big; the connector's outlet area affects the dynamic process of FPA inside air pressure greatly, but has no effects on the dynamic process of turning angle; moment of inertia and viscous damping coefficient have no effects on the dynamic process of FPA inside air pressure, but affect the dynamic process of turning angle greatly.

在弯曲关节模型推导的基础上，建立扭转关节的静态模型，并分析了扭转关节内腔压力，初始转角，橡胶管平均半径，橡胶管壁厚等参数对关节转角的影响，得出扭转关节的转动角度与充入FPA内腔的压缩气体压力之间基本呈线性关系，扭转关节的转角随初始角度和橡胶管平均半径的增大而增大，扭转关节的转角随橡胶管壁厚的增大而减小的结论；建立了扭转关节的动力学方程，仿真实验表明FPA的充放气过程与扭转关节的动力学过程相比时间极短，在实际系统设计和控制过程中可以忽略不计；分析讨论橡胶管壁厚，平均半径，初始角度，气体节流口面积，转动惯量，粘性阻尼系数等因素对扭转关节动态特性的影响，得出橡胶管初始壁厚的变化对扭转关节FPA内腔压力的动态响应几乎没有影响而对关节转角的响应曲线影响比较明显，壁厚较小时，关节可以得到较大的转角，并且转角的响应曲线没有超调，但上升时间长，壁厚较大时，关节转角变小，响应加快，但是有超调和轻微振荡现象，橡胶管平均半径越大，得到的关节转角越大，但是转角响应的超调量也随之增大，FPA的初始角度越大，关节的转角越大，并且超调量减小，振荡减弱，但是上升时间增大，管接头出口面积的大小对关节FPA内腔压力的建立过程影响较大，但对关节转角的动态响应几乎没有影响，转动惯量和粘性阻尼系数对FPA内腔压力的动态过程几乎没有影响而对扭转关节转角有较大影响等结论。

The invention discloses a support device for an air conditioning faceplate, which is arranged between a front faceplate of a suction inlet of a suspender air conditioning and an air conditioning casing, comprising a support component and a drive motor, wherein, the support component is a cross drive lever component formed by two connecting levers which are connected with each other with freely rotated middle part in a scissors shape, comprising a driving lever and a driven lever, wherein, the driving lever passes through the middle part of the driven lever; the middle part of the driving lever is rotatablely fixed in the middle part of the driven lever; the driving lever is driven by a step motor, has one end fixed on the step motor and the other end fixed in a chute of the faceplate capable of sliding in the chute; and one end of the driven lever is connected with a hook of the faceplate, and the other end of the driven lever is arranged in the chute of the casing and can slide in the chute.

本发明公开了一种空调面板支撑装置，设于挂式空调吸入口的前面面板和空调罩壳之间，包括支撑构件和驱动电机，所述的支撑构件是由中间部转动自由地相互连接的两连杆构成的呈剪刀状的交叉传动杆组件，包括主动杆和从动杆，主动杆从从动杆中部穿过，主动杆中部可转动地固定在从动杆中部，主动杆由步进电机驱动，一端固定在步进电机上，另一端在面板的滑槽中，可以在滑槽中滑动，从动杆一端与面板的挂钩连接，另一端在罩壳的滑槽中，可以在滑槽中滑动。

In a disk device, a base body (10) has a drawing lever (80) for inserting a disk, a discharge lever (100) for discharging the disk, and a slider mechanism for pivoting the drawing lever (80) and the discharge lever (100). The slider mechanism has a first cam groove for sliding a first pin of the drawing lever (80) and a second cam groove for sliding a second pin of the discharge lever (100). The drawing lever (80) pivots when the first pin slides in the first cam groove as the slider mechanism operates, and the discharge lever (100) pivots when the second pin slides in the second cam groove as the slider mechanism operates.

该光盘装置，在基座本体(10)上设置插入光盘的引入杆(80)、排出光盘的排出杆(100)以及使引入杆(80)和排出杆(100)转动的滑动机构；在滑动机构上具有使引入杆(80)的第一销滑动的第一凸轮槽和使排出杆(100)的第二销滑动的第二凸轮槽；通过第一销随着滑动机构的动作在第一凸轮槽内滑动，引入杆(80)进行转动，通过第二销随着滑动机构的动作在第二凸轮槽内滑动，排出杆(100)进行转动。

与torsion lever相关的网络解释 [注：此内容来源于网络，仅供参考]

Lever spring seat：变速杆弹簧座 Lever switch 杠杆开关

Lever spring 变速杆弹簧 | Lever spring seat 变速杆弹簧座 Lever switch 杠杆开关 | Lever type shock absorber 摇臂式减振器

torsion electrometer; coulomb torsion balance：扭转静电计

扭转式测力计 torsion dynamo meter | 扭转静电计 torsion electrometer; coulomb torsion balance | 磁转电流计 torsion galvanometer

torsion load：扭转荷载

torsion lever 扭杆 | torsion load 扭转荷载 | torsion machine 绕簧机