thread angle

thread angle的基本解释

-

螺纹断面角

与thread angle相关的网络例句 [注：此内容来源于网络，仅供参考]

And linking the principle of choosing computer visual inspection system hardware, the paper constructs hardware structure of visual inspection system, and develops measure software of thread geometry parameter and applies all above research results to quantificationally measure geometry parameters such as half angle of thread, coning and pitch of conical joint screw thread of graphite electrode, at last educes influencing expressions of the shelter of lead angle to half angle of thread change, it establishes theory base for error amendment.

论述了微小零件尺寸及形状误差的常用测量方法，提出了将视觉检测技术应用到微小零件尺寸及形状误差的测量中，构建了视觉检测系统的硬件结构，开发了相应的测量软件，应用第三章介绍的各种边缘检测方法对传动用滚子链链板进行了边缘检测对比实验，找出适合的边缘检测方法，并应用上述各章的研究结果对传动用滚子链链板节距以及圆形零件的圆度误差进行了测量。

The in-plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and its found that the in-plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5%. The tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space.

研究结果表明：随着缝纫密度、缝纫线直径、最大纤维偏转角和缝纫变形区宽度的增加，缝纫复合材料层合板面内等效模量逐渐降低，最大降幅一般在5%左右；缝纫复合材料层合板的拉伸强度随缝纫针距的增加而增大，随缝纫行距的增加而降低，因此缝纫密度对拉伸强度的影响程度要看具体的缝纫针距和行距。

Size 1/2"(15mm) dual connection, solder or male IPS x 3/4"(20mm) hose thread connection, angle pattern

BD1C -通径DN15双连接，焊接或外螺纹铁管连接端口 x DN20软管螺纹连接端口，角式

Hose thread connection, angle pattern

BD2C -通径DN20可锻铸铁管连接端口 x DN20软管螺纹连接端口，角式

Horizontal stresses on the thread helix angle of a nut is called what?

在螺母 螺纹螺旋角上的横向应力叫什么？

与thread angle相关的网络解释 [注：此内容来源于网络，仅供参考]

thread angle：螺纹角

thread 螺纹 | thread angle螺纹角 | thread chaser螺纹碾压

thread angle：螺纹牙形角度

thread alternating 错扣 | thread angle 螺纹牙形角度 | thread compound 螺纹油

thread angle：牙型角

基本牙型 basic profile | 牙型角 thread angle | 牙型半角 half of thread angle

thread angle：螺纹断面角

thread n 线, 细丝, 线索, 思路, 螺纹 | thread angle 螺纹断面角 | thread caliper 螺纹卡尺

normal thread angle：垂直螺纹齿形角

normal thorium sulfate ==> 硫酸钍 | normal thread angle ==> 垂直螺纹齿形角 | normal thread form ==> 标准螺纹形状