the limit

the limit的基本解释

n.

极点, 极限

与the limit相关的网络例句 [注：此内容来源于网络，仅供参考]

The authors studied carefully two numerical differential methods, finite difference method and rational polynomial technique, and pointed that FDM is the special ease of RPT when the limit state function is linear. Accordingly, FDM3 can be used for the continuous linear limit state function and RPT5 for the continuous nonlinear limit state function. For the discontinuous limit state function, RPT should be used because of the large error of FDM.

对于可靠度分析中常用的有限差分法及有理多项式法这两种数值微分方法，本文详细研究了二者间的异同及其求导结果与步长的关系，指出了对于相同的步长控制系数及取样方式，FDM是RPT在线性情况下的特例；对于连续的线性功能函数，可直接用3点FDM求导；对于连续的非线性功能函数，可用5点RPT求导；对于非连续的功能函数，应采用RPT求导。

And with these results, I delve further into the theoretical issues of MSP and the concentration is on a special class of MSP-Doob skeleton processes. Generalized limit distribution, limit distribution of these processes and conditions and the expressions for the existence of invariable measure of such processes are provided. Finally, these new results are then applied to queueing theory, reliability theory and inventory theory. A detailed study of GI/G/1 queuing model, parallel connection system model, water reservoir model and perishable inventory model is discussed. These models have already been investigated to some degree. In particular, as mentioned above, some scholars have already successfully applied the transient behavior theory of MSP to these models and transient distributions of main variables in such models have been obtained. However, the limit behavior has not been addressed. In this thesis, limit behavior of main variables in the above-mentioned models is established.

在这个基础上，对马尔可夫骨架过程的理论进一步进行了探讨，将注意力集中于一类特殊的马尔可夫骨架过程Doob骨架过程，给出了这类过程的广义极限分布、极限分布以及不变测度存在性条件和表达式，并应用这些结论于排队论、可靠性理论和存储论等领域-具体分析了GI/G/1排队论系统模型、并联系统模型、水库储水模型、易腐烂物品库存模型——这些模型都不同程度地被许多学者研究过，特别，如前面提及，已有人成功地应用马尔可夫骨架过程的瞬时性态理论，获得了上述各模型中的主要参量过程的瞬时分布，但是，却并没有探讨它们的极限性态——建立了若干关于上述各模犁的主要参量过程的极限性态的结果。

The pattern of camber die-drawing are optimized. The physical innate character of drawing with camber die is analyzed thoroughly. For the first time, the periodical relation between the limit drawing coefficient and the large longitudinal stress in dangerous section is established. Furthermore, the rationale to judge limit deforming degree is developed. Then, the limit drawing coefficient of drawing with camber die is proposed. Based on the criterion that the large stress in flange is smaller than that of limit value, the formula of drawing with camber die without wrinkles is deduced.

对拉深凹模的型式进行了优化；深入地分析了曲面凹模拉深成形的物理本质，首次定量地确定了极限拉深系数与危险断面最大径向应力的关系，提出了判断极限变形程度的依据，分析了极限承载能力，建立了曲面凹模拉深的极限拉深系数的表达式；以凸缘切向最大压应力小于凸缘切向压应力临界值为准则，推导出了曲面凹模拉深不起皱的理论表达式。

与the limit相关的网络解释 [注：此内容来源于网络，仅供参考]

go beyond the limit：超过限度

limber up 使柔软;柔和一下身体 . | go beyond the limit 超过限度 . | to the limit 到顶点,到最大限度 .

go beyond /over the limit：超过限度

130 the sky's the limit没有任何限制 | go beyond (over)the limit超过限度 | push oneself to the limit竭尽全力

to the limit：到顶点,到最大限度

go beyond the limit 超过限度 . | to the limit 到顶点,到最大限度 . | within limits 在一定范围之内 .