tack welding

tack welding的基本解释

-

平头焊接, 点焊

与tack welding相关的网络例句 [注：此内容来源于网络，仅供参考]

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

The content of this course mainly include the feature, equipment, principle and application of high efficient welding method, for example, activating flux assisted TIG welding, narrow gap TIG welding, hot wire TIG welding, oscillating arc TIG welding, plasma TIG welding tandem MIG welding, hybrid arc welding, surface tension transfer MIG welding, oscillating arc MIG welding, mixed-gas MIG welding, two wire or more SAW welding, friction stir welding and laser-MIG hybrid welding, etc.

主要内容涉及到助焊剂TIG焊技术、窄间隙TIG焊技术、热丝TIG焊技术、摆动电弧TIG焊技术、等离子弧焊技术的基本原理、设备、特点和应用。双丝焊MIG方法、复合电弧技术、表面张力过渡、摆动电弧MIG、交流MIG焊、混合气体MIG焊的原理、特点、设备和应用。双丝以及多丝埋弧焊技术、窄间隙埋弧焊技术的原理、特点和应用。搅拌摩擦焊以及激光电弧复合焊接的原理、特点、设备、应用范围。

The main provisions of the welding process assessment for this pipeline project are presented in this paper. Also the applications of some welding processes in the pipeline construction are described including semi-automatic welding process with self-protection flux core welding wire, root welding with Britain NOREAST internal welding machine plus filling and capping welding with domestic PAW-2000 external welding machine, root welding with American CRC internal welding machine plus heating welding with CRC P262 external automatic welding machine plus filling and capping welding with CRC P600 double torches external automatic welding machine.

文章介绍了该管道工程焊接工艺评定的主要规定，以及自保护药芯焊丝半自动焊工艺、英国NOREAST内焊机根焊＋国产PAW2000型外自动焊机填充盖面焊工艺、美国CRC内焊机根焊＋CRCP260外自动焊机热焊＋CRCP600双炬外焊机填充盖面焊工艺在管道施工中的应用。

与tack welding相关的网络解释 [注：此内容来源于网络，仅供参考]

tack welding：定位焊

tachometer 转速表 | tack welding 定位焊 | tag 压尖端

tack welding：点焊

clamp.夹钳 | tack welding 点焊 | butt welding 对接焊

tack welding：平头焊接

tapered allowance 削尖余量 | tack welding 平头焊接 | sputter 喷溅

tack welding：定位焊接

转轮 turning wheel | 定位焊接 tack welding | 涡轮机叶轮 turbine wheel

TW Tack Welding：定位焊

TW Total Weight 总重 | TW Tack Welding 定位焊 | Typ Typical 典型、标准