swivel bearing

swivel bearing的基本解释

-

旋转轴承

与swivel bearing相关的网络例句 [注：此内容来源于网络，仅供参考]

In order to ensure the construction process safe and the bridge structure would reach its ideal state, lots of questions in its whole construction control and swivel ereetion construction control are discussed and studied.Firstly, based on the experiences about the cable-stayed bridge's construction control, do emulational anlysis to Sui Fenhe cable-stayed bridge by using the bridge analyzing program of BSAS and Dbridge, analyze the parameters' sensitivity, study the temperature effects, discern the relevant parameter's errors about construction control and optimize its construction state.Secondly, as an example of Sui Fenhe cable-stayed bridge's swivel erection construction control, present the design and construction techniques of simple point supporting and even articulation and level swivel erection for long-span cable-stayed bridge, study its load-bearing system, balance system, power system and adjustment system in detail, check its static stability on the state of swivel erection construction and monitor the whole swivel erection construction.

首先，在斜拉桥施工控制经验的基础上，用桥梁结构分析程序BSAS和Dbridge对绥芬河斜拉桥进行了详细的施工仿真分析，参数敏感性分析，温度效应分析，施工控制影响参数误差分析和结构施工状态的最优化控制；其次，以绥芬河斜拉桥转体施工控制为例，介绍了大跨度斜拉桥单点平铰水平转体设计与施工技术，详细研究斜拉桥单点平铰水平转体支承系统、平衡系统、动力系统和调整系统，并对本桥结构转体施工做静力稳定性验算及转体过程的监控。

The main products include deep groove ball bearing, variation core roller bearing, cylinder roller bearing, british system bearing, variation core ball bearing, double row deep groove ball bearing, pillow block bearing, corner touch bearing, trust roller bearing, tapered roller bearing, and spherical roller bearing.

主营产品包括：深沟球轴承、调心滚珠轴承、圆柱滚珠轴承、英制轴承、调心球轴承、双列深沟球轴承、座架、角接触轴承、推力球轴承、圆锥滚子轴承和球面滚珠轴承。

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

与swivel bearing相关的网络解释 [注：此内容来源于网络，仅供参考]

swivel bearing：回转节轴承

swivel assembly;回转节总成 | swivel bearing;回转节轴承 | swivel caster;回转节后倾角

swivel block：转动滑块

swivel bearing 旋转轴承 | swivel block 转动滑块 | swivel block 转环滑车

swivel angle plate：转盘角板,倾转台

swivel anchor 转环锚 | swivel angle plate 转盘角板,倾转台 | swivel base 转座