support structure

support structure的基本解释

-

支承结构

与support structure相关的网络例句 [注：此内容来源于网络，仅供参考]

In order to meet the requirement of the Collector ring dipole superconducting magnet of FAIR in the process of operation, meanwhile, and to ensure the heat loads coming from the support structures to be lower than the design demands, the 3D models of support structures have been constructed with CATIA, then the calculation of low-temperature heat-load and the structure analysis have been done with ANSYS, the support structure material, 316LN+G10, is decided according to the heat-load calculation and the structure optimization, these results are necessary for manufacturing the formal magnet.

为保证FAIR收集环(Collector ring-CR)超导二极磁体工作过程中的磁场位形符合设计要求，同时保证由磁体支撑带来的热负荷小于设计要求，用CATIA软件建立了不同结构的磁体支撑3D模型，并用ANSYS有限元分析软件对建立的模型进行了低温热负荷分析和结构分析。通过比较分析的结果和对磁体支撑结构进行的进一步优化，确定了316LN+G10材料的支撑结构，为收集环超导二极磁体工程制造提供了参考。

Picker-wheel support structure was used in strip label papers of tobacco industry, but it had appeared some problems: picker-wheel vibrates easily, label paper was picked insecurely, and double-shafts generated deformation and linear bearings wear easily. The ultimate cause was founded by analyzing linear bearings stress from statics and dynamics. The original structure of double-shafts one-side support was replaced by two-side support with one fixed end and one free end.

针对FOCKE350S条盒商标纸拾取轮总成支撑结构拾取轮易振动、商标纸拾取不可靠、双轴易弯曲变形、直线轴承磨损快的情况，从静力学和动力学的角度分析了直线轴承磨损快的根本原因；并将原来双轴单侧支撑结构改为双轴双侧支撑，采用一端固定，一端游动的支撑方式。

It is embodied concretely:(1) With the adoption of grouting bolts, the cranny in wall rocks can be blocked up, the air can be isolated, the wall rocks can be prevented to be weatherized and make water, the strength of wall rocks can also be avoided to be lowered;(2) The lax broken wall rocks are commentated to a whole by liquid after they were grouted and the rock"s strength is increased, so the wall rocks become a part of the support structure by using itself and become a whole with the original rock, and the roadway is made to keep stable but not easy to be broken;(3) The spray layer wall are filled with liquid after grouting, the stress is avoided to be concentrated because the load could be evenly acted on the spray layer and the support;(4) The pressure acted on the plank can be delivered to the two sidepieces and then to the bottom by reinforcing the sidepiece; At the same time, the concentration degree of loads acted on the motherboard can be weaken because of the enlargement of the combination arch"s thickness, as result, the rock"s stress is lowered and the heaving is alleviated;(5) The common bolt is made to be fixed the whole length after grouting, the layers are connected to a integral whole and bear the weight of loads, so the support structure"s unity is increased.

具体体现在：(1)采用注浆锚杆注浆，可以利用浆液封堵围岩裂隙，隔绝空气，防止围岩风化，且能防止淋水和渗水，避免围岩被水浸湿而降低围岩的本身强度及造成的巷道变形。(2)注浆后浆液将松散破碎的围岩胶结成整体，提高了岩体强度，实现利用围岩本身作为支护结构的一部分，且与原岩形成一个整体，使巷道保持稳定而不易产生破坏；(3)注浆后使得喷层壁后充填密实，保证荷载能均匀地作用在喷层和支护上，避免出现应力集中点而首先破坏；(4)注浆后使作用在顶板上的压力能有效地传递到两帮，通过对帮的加固，又能把荷载传递到底板；同时由于组合拱厚度的加大，这样又能减小作用在底板上的荷载集中度，从而减小底板岩石中的应力，减轻底臌；(5)注浆加固后能使普通端锚锚杆实现全长锚固，它们共同将多层组合拱连成一体，共同承载，提高了支护结构的整体性。

与support structure相关的网络解释 [注：此内容来源于网络，仅供参考]

price support：价钱支持

price structure 价钱构成 | price support 价钱支持 | bargain 讨价讨价

price structure：价格构成

price regulation 价格调整 | price structure 价格构成 | price support 价格支持

price structure：价钱构成

price regulation 价钱调整 | price structure 价钱构成 | price support 价钱支持