subcutaneous injection

subcutaneous injection的基本解释

-

皮下注射

与subcutaneous injection相关的网络例句 [注：此内容来源于网络，仅供参考]

Examples Building text files with injection Building binary files using debug.exe with injection Injection and FTP Injection and remote xterms Injection and TFTP Adding a user with injection Scheduling a process with injection Pluming pipes, ports, and permissions Handles to open resources are sometimes inherited by the child process. If a protected resources is already open, the child process will have unfettered access to the resource, perhaps by accident.

范例 利用注入建立文字档利用 debug.exe 将资料注入到两进位档注入与 FTP 注入与远端 xterms 注入与 TFTP 利用注入新增一个使用者利用注入对程序进行排程利用 pipes， ports 以及权限已开启资源的处理代码有时候会被子程序所继承，也就是说如果一个受保护的资源被开启后，子程序将有可能在无意间不受限制地存取该资源。

Methods 100 cases were randomized into treatment group in which 50 cases were treated with Safflower injection via carotid artery infusion, added Safflower injection 20ml into 0.9% sodium chloride injection 60ml with the 4ml/min velocity, once a day; control group in which 50 cases were treated with venous drip of Safflower injection, added Safflower injection 20ml into 0.9% sodium chloride injection 500ml. After therapy, the curative effect、 myodynamia and hemorrheology were compared between the two groups.

将100例脑梗死患者随机分为红花注射液颈动脉灌注组50例和红花注射液静脉滴注组50例，治疗组：于0.9%氯化钠注射液60ml中加入红花注射液20ml，以4ml/min的滴速经颈动脉灌注；对照组：以红花注射液20ml加入0.9%氯化钠注射液500ml中静滴，20天后对两组疗效进行分析并观察治疗前后肢体肌力及血液流变学变化。

Correctional checking formula of melt flow ratio in injection molding was obtained by introducing a correction coefficient β which reflected the complexity degree of mold cavity. The results show that, the maximum flow ratio of 486 can be obtained when injection pressure ranges from 150 MPa to 160 MPa in Archimedes spiral mold for PP, while maximum flow ratio of 419 can be obtained when injection pressure ranges from 160 MPa to 170 MPa for PE. There is a local fluctuation phenomenon for flow ratio and corresponding injection rate in square spiral mold when injection pressure of 100, 120 and 150 MPa for PP and 130, 140 MPa for PE are reached respectively,and this phenomenon is more serious for good fluidity of melt. The average flow ratio in Archimedes spiral mold is 6% larger than that in square spiral mold for PP, and 4% for PE, the average flow ratio of PP is 19% bigger than PE in Archimedes spiral mold, and 15% in square spiral mold. The influence of the cavity profiles on the melt flow ratio is more significant for good fluidity of melt.

研究结果表明：在阿基米德螺旋线模具中，PP在注射压力为150~160 MPa时取得最大流动比485，PE在注射压力为160~170 MPa时取得最大流动比419；在方形螺旋线模具中，PP在注射压力为100，120和150 MPa，PE在注射压力为130和140 MPa时流动比及所对应的注射速率出现波动，且流动性好的熔体波动更为严重；PP在阿基米德螺旋线模具中的流动比均值较其在方形螺旋线模具中大6%，而PE大4%；在阿基米德螺旋线模具中流动比均值PP比PE的流动比均值大19%，而在方形螺旋线模具中PP的流动比均值比PE的大15%；流动性好的熔体受模具型腔轮廓特征影响大。

与subcutaneous injection相关的网络解释 [注：此内容来源于网络，仅供参考]

subcutaneous nodule：皮下结节,皮下小结

subcutaneous nodular type 皮下结节型 | subcutaneous nodule 皮下结节,皮下小结 | subcutaneous pocket hematoma 皮下袋状血肿

endermic injection：皮內注射 皮内注射

injection, intracardiac 心內注射 心内注射 | injection, intradermal; intracutaneous injection, endermic injection 皮內注射 皮内注射 | injection, intramuscular 肌內注射 肌内注射

intracutaneous injection：皮內注射 皮内注射

injection, intracardiac 心內注射 心内注射 | injection, intradermal; intracutaneous injection, endermic injection 皮內注射 皮内注射 | injection, intramuscular 肌內注射 肌内注射