station amplifier

station amplifier的基本解释

-

功率放大器

与station amplifier相关的网络例句 [注：此内容来源于网络，仅供参考]

S1 is then changed to position 1. The voltage stored on C1 is inserted between the output and inverting input of the amplifier and the output of the amplifier changes by VIN to maintain the amplifier input at the input offset voltage. The output then changes from (VOS + IbiasR2) to (VIN + IbiasR2) as S1 is changed from position 2 to position 1. Amplifier bias current is supplied through R2 from the output of the amplifier or from C2 when S1 is in position 2 and position 1 respectively. R3 serves to reduce the offset at the amplifier output if the amplifier must have maximum linear range or if it is desired to DC couple the amplifier.

接着 S1 拨到位置 1，使 C1 的电压加在放大器的输出端和反相输入端之间，(由于电容端电压不能突变，所以)输出端的电压将产生大小等于 VIN 的变化，使放大器输入端维持输入失调电压，即当开关 S1 从位置 2 拨到位置 1 时，输出端电压将从(VOS + IbiasR2)变为(VIN + IbiasR2)。S1 处于位置 2 时，放大器的偏置电流是由输出端经电阻 R2 提供的，当 S1 转向位置 1 时则由 C2 提供。R3 的作用是降低输出失调电压，如果要求放大器具有最大的线性范围，或者采用直流耦合，就应该使用该电容。

The objectives of this paper were to investigate the simulation and design of continuous multiple-station rolling forming process for a U-Section Steel Bar by CAE software-DEFORMTM Due to the limitation of elements number using a short strip 120mm went through all the stations to simulate the real continuous rolling forming on factory The roller gap was fixed as 0 30mm roll speed was 20 rad/sec and progressive angles were all equal for each rolling process which were the formed angle divided by by the number of station Three rolling processes were selected with 6 9 and 12 stations respectively During simulation processes two cases occurred Case A the strip was through a single station Case B the strip across two stations Because the strip laterals side was stretched and twisted during the process The model of case B closer to the practical process than case A and the calculated stress and strain on the tip of U section for case A were lower than these for case B by up to 15% From the result of case B for each process the stress for 12-station process was smallest 9-station process second and 6-station process next Because less-station can save larger cost and forming time but the bigger stress and strain for 6-station caused wrinkles on lateral sides not found on 9-station and 12-station Therefore 9-station process was a more suitable design than 12-station process smaller stretched and twisted and stress The progressive angles for 12-station was 7 5?

本文主要是以DEFORMTM有限元素软体模拟U型钢片连续道次成型与单一道次成型以确认单一道次模拟的是否可取代连续道次模拟之研究。因DEFORMTM 软体对於网格元素上的限制故使用较短素材120mm通过所有的成型站以模拟工厂实际连续成形方法。辊轮间隙固定为0 3mm；辊轮转速为20 rad/sec；弯曲角度的方法为将成型角度平均除以成型站数。有三种辊轮成型方式被选择分别为6站，9站，与12站。在模拟的过程中有两种现象会产生 Case A，素材通过单一成型站。Case B，素材会通过两个成型站。因为在模拟过程中素材的两端会有拉应力与扭力。Case B的模拟比Case A像实际的制程，并计算应力与应变在U型断面的Tip部中可发现Case A比Case B低约15%。从Case B的每站的结果可以得知，12站的成型应力最小，9站次之，6站最后。

The invention discloses a DC/DC circuit, comprising a PWM controller, a current amplifier, a peak current comparator, an error amplifier, a main switch, a synchronous switch and also an operational amplifier. The non inverting input end of the operational amplifier is used for coupling with input voltage or voltage reference, or used for coupling with the input voltage and the voltage reference; the inverting input end of the operational amplifier is used for coupling with the voltage reference or ground, and the output end thereof is connected with the non inverting input end of the error amplifier.

本发明公开了一种DC/DC电路，包括PWM控制器、电流放大器、峰值电流比较器、误差放大器、主开关和同步开关；还增设运算放大器，其同相输入端用于与输入电压或基准电压耦合，或用于同时与输入电压和基准电压耦合；其反相输入端用于与基准电压或地耦合，其输出端与所述误差放大器的同相输入端连接。

与station amplifier相关的网络解释 [注：此内容来源于网络，仅供参考]

Filling Station：加油站

加油站在美国的叫法有多种,直译成中文的有:汽油站(Gas Station)、燃料站(Fuel Station)、加油站(Filling Station)以及服务站(Service Station)等. 在美国公众中"服务站"(Service Station)已是一个琅琅上口的叫法,作为"加油站"的代名词被广泛认可和接受. .

gas station：汽油站

加油站在美国的叫法有多种,直译成中文的有:汽油站(Gas Station)、燃料站(Fuel Station)、加油站(Filling Station)以及服务站(Service Station)等. 在美国公众中"服务站"(Service Station)已是一个琅琅上口的叫法,

station pointer：三脚分度仪

station master 站长 | station pointer 三脚分度仪 | station to station call 叫号电话