spline broach

spline broach的基本解释

-

[机] 方栓槽拉刀

与spline broach相关的网络例句 [注：此内容来源于网络，仅供参考]

Spline Broach complexity of the design process, the geometric parameters, many of which need to look-up table and complex calculation to determine the parameters of a certain size, Design Spline Broach all forms and formulas into C language are procedures, through a simple C program calls, importation Spline Broach the technical parameters can be accurately its design parameters, Finally, all the parameters of integrated print out data tables, thus simplifying the complex Spline Broach design process, and meet the design requirements.

花键拉刀设计过程复杂，几何参数多，许多都需要查表和复杂的计算来确定某一参数尺寸，把花键拉刀设计中所有表格和计算公式都编成C语言程序，通过简单的C程序调用，输入花键拉刀的技术参数就可以准确得到其设计参数，最后把所有的参数值综合打印出数据表格，从而简化了复杂的花键拉刀设计过程，且达到了设计的要求。

Spline Broach complexity of the design process, the geometric parameters, many of which need to look-up table and complex calculation to determine the parameters of a certain size, Design Spline Broach all forms and formulas into C language are procedures, through a simple C program calls, importation Spline Broach the technical parameters can be accurately its design parameters, Finally, all the parameters of integrated print out data tables, thus simplifying the complex Spline Broach design process, and meet the design requirements.

花键拉刀设计过程复杂，几何参数多，许多都需要查表和复杂的计算来确定某1参数尺寸，把花键拉刀设计中所有表格和计算公式都编成C语言程序，通过简单的C程序调用，输入花键拉刀的技术参数就可以准确得到其设计参数，最后把所有的参数值综合打印出数据表格，从而简化了复杂的花键拉刀设计过程，且达到了设计的要求。

Though comparing Canny operator and center B spline dyadic wavelet, the following conclusion is proven in this dissertation: a Center B spline function has tight support and Canny operator hasn't. b Center B spline function asymptotic convergence to Gaussian function and the derivative of Center B spline function asymptotic convergence to Canny operator. c The derivative of fourth order center spline B function is more suitable as a optimal edge detector than Canny operator. d Center B spline function can balance the smoothing and approximation of original data, and the fourth center B spline function is the only optimal solution of two order smoothing problem. e The error between the valve of time-frequency uncertainty of the fourth center B spline function and the lower bound of time-frequency uncertainty does not exceed 0.143% of the lower bound. f The derivative of center spline B function can construct a stability dyadic wavelet and can give a fast algorithm for multiscale edge detection, but Canny operator can do neither.

作者给出了Canny算子与中心B样条二进小波严格的比较证明，得出如下结论：a中心B样条函数具有紧支集，Canny算子不具有紧支集。b中心B样条函数的极限收敛于高斯函数，中心B样条函数的导数收敛于Canny算子。c四阶中心B样条函数的导数比Canny算子更接近最佳边缘检测滤波器。d中心B样条函数比高斯函数更能兼顾对原函数平滑和逼近的折中要求，并且四阶中心B样条函数是二阶逼近问题的唯一最优解。e四阶中心B样条函数的时频测不准关系值与时频测不准关系下界的逼近误差不超过0.143％。f中心B样条函数的导数可以构成稳定的二进小波，存在快速的多尺度算法；而Canny算子不构成稳定的二进小波，无法给出快速的多尺度算法。

与spline broach相关的网络解释 [注：此内容来源于网络，仅供参考]

spline broach：方栓槽拉刀

spanner 扳手 | spline broach 方栓槽拉刀 | square 直角尺

spline broach：花键拉刀

splicing machine 接片机 | spline broach 花键拉刀 | spline coupling 花键联轴节

spline broach：方栓槽拉刀,花键拉刀

splicing tape 编接带 | spline broach 方栓槽拉刀,花键拉刀 | spline connection 花键连接

spline push broach：花键推刀

spline pinion cutter 花键插齿刀 | spline push broach 花键推刀 | spline shaft grinding machine 花键轴磨床

involute spline broach：渐开线拉刀

involute push broach 渐开线推刀 | involute spline broach 渐开线拉刀 | involute spline gear shaper cutter with taper shank 锥柄渐开线花键孔插齿刀