slipper piston

slipper piston的基本解释

-

滑块活塞

-

滑履活塞

与slipper piston相关的网络例句 [注：此内容来源于网络，仅供参考]

According to the acoustic model of piston slap noise, how the parameters affect the piston slap noise at different rotate speed was discussed. And those parameters were piston clearance, piston pin offset, connect rod ratio, piston skirt stiffness, crank shaft offset, height of piston's gravity center, total length of piston skirt, vertical position of piston-pin axis and under part length of piston skirt.

借助建立的活塞拍击噪声理论声学模型，深入探讨了配缸间隙、活塞销偏移量、连杆比、活塞裙部刚度、曲轴轴线偏移量、活塞质心高度、活塞裙部总长度、活塞销轴线竖直方向位置和活塞裙部下段长度等主要影响参数在不同的转速下对活塞拍击噪声的影响规律，初步总结出活塞低拍击噪声设计和改进的基本规律。

Caused by disc brake on the brake Wheel Cylinder could not return to places 4 possible: First, 5 foot brake valve exhaust port blocking, high-pressure gas instinct platoon atmosphere, caused by gas-liquid master cylinder of the spring could not return to place, resulting in the system move oil, brake disc brake Wheel Cylinder Piston top dead and could not return to places; second is to the disc brake master cylinder gas-liquid pipeline blockage, resulting in brake Cylinder piston can not return to place; third master cylinder of the gas-liquid Spring itself can not return to position, brake fluid under high pressure gas can not return Axial pump to gas-liquid master cylinder reservoir chamber, resulting in brake Cylinder piston can not return to places; Fourth Wheel Cylinder piston disc brake system, due to moving fluid dirty or rusty card dead and can not return to the piston position.

造成盘式制动器上的制动分泵不能回位有4种可能：一是脚制动阀5的排气口堵塞，高压气体本能排人大气，造成气液总泵的弹簧不能回位，导致制动油将盘式制动器的制动分泵活塞顶死而不能回位；二是气液总泵至盘式制动器的油管堵塞，造成制动分泵活塞不能回位；三是气液总泵的弹簧本身不能回位，制动液在高压气体作用下，不能回到气液总泵的储油室，从而造成制动分泵活塞不能回位；四是盘式制动器制动分泵活塞由于制动液太脏或活塞生锈卡死而不能回位。

When the flow through the balance of the piston damping the flow of holes increases, the balance of the piston, the next increase in pressure on both sides of a balanced increase in the distance the piston increases, and vice versa reduced; and also because the spring stiffness is very small, so that shift the balance of the piston pressure required very few changes, so the flow through the Poppet head is not much change, so the first opening Poppet very few changes, to mention the pressure of moving the first opening can be said to remain unchanged, that is, when the pilot valve spring after a set, Poppet Head was opened, the balance piston chamber pressure remained basically unchanged.

当流经平衡活塞上阻尼孔的流量增加时，平衡活塞上、下两侧的压差增加，平衡活塞上升距离增加，反之则减小；又因为弹簧的刚度很小，使平衡活塞上移所需压差变化很小，所以通过提动头的流量变化也不大，因此提动头的开口变化很小，提动头开启的压力可以说是不变的，亦即当先导阀的弹簧一经设定后，提动头被打开时的平衡活塞上腔的压力基本保持不变。

与slipper piston相关的网络解释 [注：此内容来源于网络，仅供参考]

slipper piston：滑裙活塞

间接冷却式活塞 indirect cooled piston | 滑裙活塞 slipper piston | 活塞速度 piston speed

slipper piston：滑履活塞

slipper collector 滑动集电器 | slipper piston 滑履活塞 | slipper satin 鞋面花缎

slipper piston：活塞速度

indirect cooled piston 滑裙活塞 ^Ac oi5) | slipper piston 活塞速度 ARNp,"?{o | piston speed 活塞顶部 [[Q| U

slipper piston：拖鞋式活塞

拖鞋式活塞 slipper piston | 集电缆 slipper shoe | 滑动 slipping

piston slipper：活塞活动部分

piston slide valve ==> 活塞式滑阀 | piston slipper ==> 活塞活动部分 | piston speed ==> 活塞速度