slip crack

slip crack的基本解释

-

滑裂, 层裂, 起层(由于冲压下料或剪切所引起), 滑移裂纹

与slip crack相关的网络例句 [注：此内容来源于网络，仅供参考]

Therefore has carried on the next experiment: For the proof slip of paper dry scope migration is but because of receives the earth's attraction the influence to concentrate toward the slip of paper lower part, we have carried on the next experiment, we cut the slip of paper the long strip, then changes the level laying aside, because whether there is can't such slip of paper both sides underneath the space cause the hydro energy downward to concentrate create the experimental result the difference, after the experiment discovered, after has removed this difference, the slip of paper both sides dry need the time is nearly same, but according to above experiment, we arrived following conclusion, the slip of paper dry scope is downward moved from on downward migration because of the slip of paper in moisture content by the attraction attraction, causes under the slip of paperAbove the hydraulic modulus also must be many, above the natural slip of paper falls very quickly on the few water on the evaporation, but under many moisture content need more time can evaporate, causes the slip of paper dry scope most above downward to increase slowly from the slip of paper.

急！！！物理翻译中翻英请帮帮忙於是进行了下一个实验：为了证明纸片〈paper sheet〉乾燥范围的移动〈boundary of drying〉是因为受到地心引力的影响而往纸片下部集中，我们又进行了下一个实验，我们把纸片剪成长条状，然后改为水平放置，这样纸片两端就不会因下方有无空间使水能往下集中而造成实验结果的差异，实验后发现，去除了这个差异后，纸片两端乾燥所需的时间几乎相同，根据以上的实验，我们的到了以下的结论，纸片乾燥范围从上往下移动是因为纸片中的水分被引力吸引而往下移动，使得纸片下面的水比上面还要多，自然纸片上面就少量的水很快就蒸发掉，而下面较多的水分需要更多的时间才能蒸发完，使得纸片乾燥的范围从纸片最上面慢慢往下增加。

The main research tasks and results are as follows:(1) Through comparing the stress intensity factor of compact tension specimen calculated by finite element software with the theoretical value, the feasibility of calculating fracture parameters of crack tip in ABAQUS software was verified.(2) The relationship between the elastic modulus of the material and research scale was studied based on deriving the cohesive stress theory and other relevant theories. And the elastic modulus of the material on meso-scale was determined.(3) Global model and sub-model of the finite element were built in th...e macro-scale, and stress-strain field nearby the crack tip was analyzed, and the results show that the detailed stress-strain in the crack tip could be obtained by using the sub-model technique.(4) In meso-scale, the crack growth model was also established by assuming the crack propagating along the grain boundary, and the detailed stress-strain field in the crack tip was obtained.(5) The effect of crack length on Von Mises stress, and maximum principal stress and strain was analyzed in meso-scale when equivalent KI equals 30MPa.m1/2. And the results show that except for crack tip area, the stress-strain distribution in whole specimen is not affected.

主要完成研究内容和取得成果如下：(1)利用有限元软件计算出紧凑拉伸试样的裂纹尖端应力强度因子KI值，其结果与理论值一致，从而验证了利用ABAQUS计算裂纹尖端相关断裂参量的可行性；(2)在研究内聚应力等相关理论的基础上，推导出了研究尺度与材料弹性模量的近似关系，并确定了介观尺度上的弹性模量；(3)在宏观尺度上建立了全局有限元计算模型和子模型，得到了裂纹尖端应力应变场分布，结果表明利用子模型技术获得比较准确的裂纹尖端应力应变场分布是可行的；(4)在介观尺度上利用平均晶粒尺度的方式建立了裂纹沿晶扩展模型，得到了裂纹尖端断裂过程区的微观应力应变场；(5)当应力强度因子为30MPa.m1/2时，分析了介观尺度上在裂纹沿晶扩展过程中裂纹长度对Mises应力、最大主应力和应变的影响，结果表明，裂纹扩展长度对试样整体应力应变分布影响不大，而对裂纹尖端区域有较大影响；(6)介。。。

Crack propagation problems under the influence of the edges of the crack subjected to homogenous loads, the origin of the coordinates subjected to concentrated increasing loads, the central zone of the edges of the crack subjected to homogenous loads, the certain point of the edges of the crack subjected to moving unit step loads, the origin of the coordinates subjected to moving increasing loads Px m, the edges of the crack subjected to instantaneous impulse loads, the edges of the crack subjected to moving concentrated variable loads, the origin of the coordinates subjected to point loads, the edges of the crack subjected to a constant moving concentrated loads and the origin of the coordinates subjected to instantaneously moving impulse loads are studied respectively, and the analytical solutions of dislocation distribution function have been obtained.

同时对裂纹面受均布载荷、坐标原点受集中增加载荷、裂纹面中心区受均布载荷、裂纹面上某点受运动阶跃载荷、坐标原点受运动增加载荷Px m、坐标原点受瞬时冲击载荷、裂纹面受运动集中变载荷、坐标原点受集中载荷、裂纹面受常数运动集中载荷、坐标原点受瞬时运动冲击载荷作用下的裂纹扩展问题分别进行了研究，获得了位错分布函数的解析解。

与slip crack相关的网络解释 [注：此内容来源于网络，仅供参考]

slip cover：滑顶

slip coupling 滑动联轴器 | slip cover 滑顶 | slip crack 滑裂

slip rope：回头缆;准备解脱的缆绳

slip ring 汇电路 | slip rope 回头缆;准备解脱的缆绳 | slip stopper slip spacing increment 滑道间距增量

slip stopper：滑钩链掣

slip stopper slip spacing increment 滑道间距增量 | slip stopper 滑钩链掣 | slip stream 滑流螺旋桨尾流推进器流推进器尾流