size rolls

size rolls的基本解释

-

定径辊

与size rolls相关的网络例句 [注：此内容来源于网络，仅供参考]

First, this article introduced 2 grade of rotary kiln principle of work and the equipment, to rolled the circle mechanics behavior to carry on the analysis, proposed - rolled the circle - under roller's rotary kiln overall modelling based on the tube body - kiln liner - big tooth ring, to rolled the circle - under roller's contact stress to carry on the finite element analysis the method, and obtained rolled the circle contact stress the size and the distribution rule, finally indicated that rolled the circle contact stress mainly to have two main peak values and the sudden change in one week, appeared is rolling the circle and the under roller contact area; Then, rolls the circle the stress to regard as is the principal stress unknown plane stress test, the use quite mature modern test technology, proposed rolls the circle stress test the principle and the plan, and to rolled the circle the stress to carry on the scene test, the stress which the scene test analysis result and the finite element analysis calculated has compared, had proven the whole method modelling's finite element analysis method's rationality and rolled the circle - under roller contact stress the result accuracy; Finally, uses ANSYS APDL the re-development technology, in view of 2 grades of rotary kilns, rolled the circle - under roller contact stress the overall finite element analytic method to carry on the re-development.

首先，本文介绍了2档回转窑工作原理和装置，对滚圈的力学行为进行了分析，提出了基于筒体-窑衬-大齿圈-滚圈-托轮的回转窑整体建模，对滚圈-托轮的接触应力进行有限元分析的方法，并得到了滚圈接触应力的大小和分布规律，结果表明滚圈接触应力在一周内主要存在两个主要的峰值和突变，都出现在滚圈与托轮接触区域；然后，把滚圈的受力看成是主应力未知的平面应力的测试，利用比较成熟的现代测试技术，提出了滚圈应力测试的原理和方案，并对滚圈的应力进行了现场测试，现场测试分析结果与有限元分析计算出的应力相比较，证明了整体法建模的有限元分析方法的合理性和滚圈-托轮接触应力的结果的正确性；最后，利用ANSYS的APDL的二次开发技术，针对2档回转窑，就滚圈-托轮接触应力的整体有限元分析法进行了二次开发。

Moreover, the hot compressive deformation behavior of the RS/PM AZ91 magnesium alloy and AZ91 alloy matrix composite were also investigated, the conclusions are drawn as follows:1. The processing parameters of the atomization-twin rolls quenching technology were optimized as follows: the diameter of the nozzle 1mm, the wheel velocity 25m/s, the pressure of atomization gas 0.3MPa and Ar gas for melt injection 0.1MPa. The RS AZ91 alloy flakes exhibited fine and uniform microstructures. When the flakes were extruded at 673K, extruded velocity of 0.1mm/min and extrusion ratio of 25:1,the magnesium alloy rods with clean surface, uniform dimension and excellent mechanical properties were obtained.2. The RS AZ91 magnesium alloy powders prepared by atomization-twin rolls quenched technology exhibited fine equiaxed grains with the grain size of 1-3μm, the phase constituent included supersaturate solid solution phaseα-Mg and miner fineβ-Mg_(17)Al_(12) phase. The as-extruded materials also exhibited equiaxed grains with the size of 5-7μm and a large number of fineβ-Al_(12)Mg_(17) and fewer AlMg_2Zn phases were detected in the alloy.

本文还研究了快速凝固/粉末冶金AZ91镁合金热压缩变形流变应力行为，快速凝固/粉末冶金法原位生成Mg_2Si增强AZ91镁基复合材料，经过系统的研究，获得如下结论：1、雾化-双辊急冷法在下列工艺参数组合下：双辊线速度25m/s；喷嘴直径1mm；熔体压射压力0.1MPa；雾化气体压力0.3MPa。，可获得宏观尺寸细小、微观组织均匀细小、综合性能优良的的快速凝固AZ91镁合金细碎箔带，快速凝固箔带在挤压温度为673K、挤压速度为0.1mm/min，挤压比为25：1时，可获得的外表光洁、尺寸均匀、组织性能优异的镁合金棒材。2、雾化-双辊急冷法制备的AZ91镁合金粉末态为细小等轴晶组织，晶粒尺寸1-3μm，组织为α-Mg过饱和固溶体和微量的细小β-Mg_(17)Al_(12)相组成；粉末挤压棒材为等轴晶组织，晶粒尺寸5-7μm，组织中含有大量细小的β-Al_(12)Mg_(17)以及AlMg_2Zn析出相，室温力学性能，抗拉强度383MPa，屈服强度275MPa，断后伸长率7.5%。

Self-adjustable type turning rolls is applied to the welding of cylinders and can be self-adjusted to the size of the cylinder. Various specifications are available for the users and large-tonnage rolls can be customized.

自调式滚轮架适用于圆形筒体的焊接，可根据筒体大小自行调节，有多种规格可供用户选择，大吨位的可代为设计制造。