secant curve
- secant curve的基本解释
-
-
正割曲线
- 更多网络例句与secant curve相关的网络例句 [注:此内容来源于网络,仅供参考]
-
The secant modulus is used to calculate final settlement of high-stacked soil, compared with the result of e ~ p curve, the error is in the limit of tolerance.
同时将割线模量计算沉降的方法应用到高填方自身作用下的最终沉降计算中,通过与应用e~p曲线计算的结果进行比较,其误差在允许范围之内。
-
The results indicate that its dynamic stress-strain curve is hyperbolic type. The dynamic strain of LCES decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency when it is subjected to the same dynamic stress. At the same dynamic strain, the dynamic secant elastic modulus E_(sec of LCES increases and the damping ratio decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency. The curves ofσ_d~ε_d,E_~ε_d and D~ε_d with different EPS content intersect respectively, the trend of LCES deformation characteristic is inversely proportional to EPS content near the intersection. The value of dynamic strain at the intersection is about 0.5%~3.0%, the magnitude of which is related to the mixing proportions and confining pressure.
试验结果表明,LCES的动应力应变骨干曲线形态符合双曲线;在相同的动应力作用下,LCES产生的动应变随着固结压力、水泥掺量、试样养护龄期和振动频率的增大而减小;在动应变相同的情况下,随着固结压力、水泥掺量、试样养护龄期和振动频率的增大,LCES的动模量增大而阻尼比减小;随着加载次数的增大,LCES的动模量在开始阶段显著降低,然后趋于稳定,但当加载次数达到几百次时,动模量又有增大的趋势;不同EPS掺入比的LCES的动应力应变骨干曲线、动模量随应变变化曲线和阻尼比随应变变化曲线都发生了相交,交点前后EPS掺入比的大小对LCES动力变形特性的影响趋势是截然相反的,交点处的动应变值一般在0.5%~3.0%范围内变化,其大小与LCES的配比以及固结压力有关。
-
At the same time, under the condition of small strain, firstly, the secant shear modulus was always larger than the tangent shear modulus. Secondly, when the logarithmic coordinates were applied to describe shear strain, the decrease of shear modulus with shear strain could be expressed by reversed S shape curve with two inflexion points, and through analyzing and validating, the deduced equation could perfectly reflect this characteristic. Finally, different stress paths and strain areas would lead to different attenuation trends.
而且,在小应变范围内,割线剪切模量总是大于切线剪切模量;当剪切应变采用对数坐标表示时,剪切模量随着剪切应变的增加而衰减,且衰减的规律都可以表示为带有两个拐点的反S型曲线,经分析验证本文所得公式3可以对此特性进行很好地反映;但应力路径、应变范围不同其衰减幅度不同。
- 更多网络解释与secant curve相关的网络解释 [注:此内容来源于网络,仅供参考]
-
secant curve:正割曲线
正割圆 secant circle | 正割曲线 secant curve | 正割公式 secant formula