scumming

scumming的基本解释

-

[变形] scum的现在分词

-

[机] 起泡沫, 泛霜, 起脏, 撇渣

与scumming相关的网络例句 [注：此内容来源于网络，仅供参考]

According to quality problems of wall,it analyzes causes of cracks、scumming and abscission in mass cement sand pulp wall plastering ,and puts forward prevention measures to ensure beautiful view of wall.

针对工程墙面存在质量病害的现象，分析了大面积水泥砂浆墙面抹灰出现裂纹、泛霜、脱落的原因，介绍了其防治措施，以保证墙面的美观效果。

Based on the scumming of architecture ,it analyses the reasons and affecting factors of scumming,discusses the merits and defaults of the existed solving methods,and puts forward the develop direction of preventing the phenomenon of damage the architecture beauty even safety,to prospect to solve the problems on basis.

从建筑物泛霜的现象出发，分析了产生泛霜的原因及影响因素，探讨了现有解决措施的优缺点，并提出了这一危害建筑物美观甚至安全的现象的发展方向，以期从根本上解决泛霜现象。

The study revealed, in the runnability, dynamic emulsion stability of ink, in offset printing, the stability of soy ink is about 0.905 gram-meter, and in web printing is about 1.4 gram-meter both better than traditional ink, so easier to cause some problems such as scumming , mottle, dot gain, and low printing density, etc.

最后得到结论，黄豆油墨适机性方面，在动态乳化稳定性，张页印刷时较传统佳约0.905 gram-meter，轮转印刷时较传统佳约1.4 gram-meter，因此较不易造成失败的水墨乳化、油墨失去流动且不再转移到印版、引起版糊与版污、造成印刷浓度降低等。

Static emulsion property of ink, the emulsion rate of soy ink is 29.6% higher than traditional ink, but cyan of soy is about 38.3% exceed the acceptable range, easier to pickup too much water, and cause dot gain, drying slowly, scumming, low printing density, etc.

在静态乳化，乳化率约29.6%较传统高，其中青墨乳化水量偏高约38%，较易导致网点扩大，乾燥缓慢、版污、色彩强度被冲淡等问题。

与scumming相关的网络解释 [注：此内容来源于网络，仅供参考]

Scumming：脏版

脏版(scumming) 因印版润湿不良,造成空白部分着黑. 网点增大(dot gain) 承印物上网点面积比印版上相对应部分的网点面积增大. 堆墨(ink piling) 油墨和其他物质沉积在墨辊或橡皮布上,形成浮雕状的沉积物,影响油墨和印迹转移.

Scumming：乏光(搪)

scum浮霜(陶);浮沫(玻) | scumming乏光(搪) | scurf碳积

Scumming：起泡沫

出渣孔 scum hole | 起泡沫 scumming | 煤粉 sea coal

Scumming：印刷版面沾污,糊版

scum mark 油(脂)斑(点)(纸病) | scumming 印刷版面沾污,糊版 | scumming roll 电动调向辊

scumming roll：电动调向辊

scumming 印刷版面沾污,糊版 | scumming roll 电动调向辊 | scurf resistance 耐磨强度