英语人>词典>英汉 : screw hole的中文,翻译,解释,例句
screw hole的中文,翻译,解释,例句

screw hole

screw hole的基本解释
-

螺丝孔(有螺纹的), 螺钉孔, 螺孔

更多网络例句与screw hole相关的网络例句 [注:此内容来源于网络,仅供参考]

Abstract] objective to explore the accuracy and safety of safety drillprepared for cervical pedicle screw trajectory.methods fourteen adult cadaver specimens of cervical spine(c3~c7)with intact structures including ligaments and perivertebral muscles were reserved and used.according to the radiographic measurements,safety drill was inserted into cervical pedicle individually.the evaluation of the drill's trajectory was carried out by ct scan and three-dimension reconstruction and autopsy.results one hundred and forty drill's trajectories were made.9 holes failed with a perforation rate of 6.4%.conclusion the safety drill prepared for cervical pedicle screw hole is safe and effective and can be applied and popularized clinically.

目的 探索安全钻头应用于颈椎弓根螺钉孔道钻探的安全性与准确性。方法随机取14具福尔马林浸泡的成人颈椎标本(c3~c7),保留完整的脊柱三柱结构及相关的韧带和椎旁肌,根据影像学测量的进钉点和进钉方向,模拟颈椎后路手术过程。选用安全钻头,进行实际的颈椎弓根螺钉孔道的钻探,将孔道行ct扫描,并斜位三维重建孔道形态,并以肉眼直视观察结果为金标准,评价孔道钻探的成败。结果钻探孔道准确率89.3%(125/140),穿孔率6.4%(9/140)。结论安全钻头应用于颈椎弓根螺钉孔道钻探的安全性与准确性均较高,可以在临床上推广使用。

After nail implanted and in the case of compression load, the highest effective stress occurred in the screw hole of nail (nail-screw interface) for comminuted tibial fracture. While as a complete simple fracture the highest stress presented in the outer screw-cortical bone interface.

在最大生理负载下时,一体成型的骨钉最大有效应力发生在骨折处的骨钉上,新设计的分节式骨钉则发生在骨折区域邻近处两节间的界面。

It is common practice to use the same distal locking screw of the nail if this surgery is performed, however, there is a risk of the new drill hole "cutting out" into the old screw hole.

如果手术已经完成,一般会利用相同的远端锁钉,但是,有可能这个新的锁钉孔滑移进入原有的锁钉孔。

更多网络解释与screw hole相关的网络解释 [注:此内容来源于网络,仅供参考]

bleed screw:放气螺栓

bleed plug 放气塞 | bleed screw 放气螺栓 | blind hole 不贯穿孔;闭孔;盲孔

blind hole:盲孔

装配为副本 可以利用"盲孔 盲孔"(Blind hole) 或直孔来放置垃圾钉.当垃圾盘组件包含螺钉时,会使用螺纹 盲孔孔. 另请参见 关于元件 关于螺钉 螺钉将两个元件连接在一起.带肩螺钉与碰锁很相似,用于控制板的移动.单击"EMX">"螺螺钉"(Screw),

screw tap:丝锥

2783.板牙 screw plate | 2784.丝锥 screw tap | 2785.中心孔 center bore center hole center opening