scanning speed
- scanning speed的基本解释
-
-
扫描速度, 扫描速率
- 相关歌词
- At 30,000 Ft.
- 拼写相近词组、短语
- scanning speech
- 更多网络例句与scanning speed相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Thus, the spherical-crown and saddle-shaped surfaces were demonstrated. Consequently, the basic rules and key technology of bending forming using plasma arc in practical work were obtained and the application level of the flexible forming using plasma arc had been further improved. The effects of the main parameters including power, scanning speed, scanning distance and scanning sequence had been investigated.
对成形中出现的棱角效应进行了机理分析和数值计算，结果表明棱角效应是板材沿扫描线方向受几何约束产生了较小的压应变及在扫描线上、下表面的收缩量不同所造成；提出了通过分段扫描解决棱角效应的方法，明显提高了成形质量。
-
The laser-cladding layeron the alloy consists of matrix phase of over-saturation solid solution γ and complexhexagonal carbide M_7C_3. Under certain condition, with fast laser scanning speed, the oversaturation solubility of elements increases in γ, and the precipitation of the complexcarbide M_7C_3 decreases, so that the microhardness increases and the wear resistance de-creases. But at slower laser scanning speed, more complex carbide M_7C_3 may precipitate, andthe wear resistance may be improved. Therefore, it is believed that the principal factor in im-provement over wear resistance is the precipitation of carbide M_7C_3, while overmicrohardness is the over-saturation solubility of elements in matrix phase.
表明：(1)激光熔覆合金层是由过饱和的γ基体相和复杂的六方M_7C_3碳化物相所组成(2)在其他参数不变的情况下，随激光扫描速度的提高，γ基体相过饱和度增大，而析出的碳化物含量减少，因而合金层的硬度升高，耐磨性有所下降；而降低激光的扫描速度，碳化物M_7C_3析出增加，有利于提高合金层的耐磨性、因此碳化物M_7C_3析出量是提高耐磨性的主要因素，而增加基体相γ的过饱和度则是硬度提高的主要因素
-
The mathematical model by which the forming time can be precisely calculated is ratiocinated. This model shows that in SLS the scanning "delay" phenomenon can make the actual forming time greatly exceed the theoretical time, and the total number, total length of the scanning lines and the scanning speed have different effects on the scanning "delay".
本文推导出了SLS成型时间精确计算的数学模型，该模型显示在SLS加工中的扫描&延时&现象会造成实际成型时间远远大于理论时间，并且扫描线条数、扫描线总长和扫描速度对扫描&延时&有不同程度的影响。
- 更多网络解释与scanning speed相关的网络解释 [注：此内容来源于网络，仅供参考]
-
scanning speed：扫查速度
Scanning sensitivity 扫查灵敏度 | Scanning speed 扫查速度 | Scanning zone 扫查区域
-
scanning speed：扫描速率
"scanning raster ","扫描光栅" | "scanning speed ","扫描速率" | "scanning spot ","扫描光点"
-
scanning speed：走査速度
scanning point 走査点 | scanning speed 走査速度 | scanning spot 走査点