roundness ['raundnis]

roundness的基本解释

n.

圆, 圆形, 球形

与roundness相关的网络例句 [注：此内容来源于网络，仅供参考]

Based on the criteria of roundness error, the definition of the circumscribed circle and inscribed circle with the least roundness error was given. The solution to the circumscribed circle and inscribed circle with the least roundness error was proposed when they met with the criterion of obtuse triangle.

根据圆度误差评定的判别准则，给出具有最小误差的外接圆和内接圆的定义，并提出了解决具有最小误差的外接圆和内接圆满足钝角三角形准则时的误差评定方法。

Roundness tolerance of pitch diameter Roundness tolerance for a minimum of 345o circumferential arc of the pitch diameter shall not exceed .002 inch (0.051 mm) total, or one half the pitch diameter tolerance if the pitch diameter tolerance is less than .004 inch (0.102 mm); roundness tolerance of the remaining 15o maximum circumferential arc shall not exceed .004 inch (0.102) total, provided such tolerance does not result in excrescence on the thread flank.

圆度公差沥青直径圆容忍最低限度的345o圆周弧音高直径不得超过0.002英寸（ 0.051毫米）总，或一的一半，足球场直径公差，如果沥青直径公差小于0.004英寸（ 0.102毫米）；圆的耐受性，其余15o最大周弧不得超过0.004英寸（ 0.102 ），共计提供这样的宽容不会导致在excrescence对线程的侧翼。

An analysis revealed very significant positive correlation between trophozoite area and nucleus area (r=0.54, P .01), trophozoite volume and nucleus volume(r=0.47, P .01), and negative correlation between trophozoite area and trophozoite roundness (r=-0.29, P .01), no significant correlation between nucleus roundness and trophozoite roundness.

相关分析显示滋养体与核的面积(r=0 。5 4 ，P 。0 1)、滋养体与核体积(r=0 。4 7，P 。0 1)相关性有显著性意义，滋养体面积和核圆度呈负相关(r=- 0 。2 9，P 。0 1)，滋养体圆度和核圆度之间无相关性。

与roundness相关的网络解释 [注：此内容来源于网络，仅供参考]

roundness：圆度

地质学名词:圆度(roundness)又称磨圆度(psephicity),是指岩石或矿物颗粒在搬运过程中,经流水冲刷,互相撞击之后,棱角被磨圆的程度. 颗粒棱角越多越尖锐则圆度越差;反之棱角圆滑,圆度就好. 碎屑颗粒圆度可用公式P=Σr/N.R计算求出.

roundness：真圆度

此外,本系统藉由自动调整阀值(threshold)与三值化、边缘侦测(edge detection)及最小平方法(least square method)等运算求取每一圆孔的真圆度(roundness),以进行更准确的几何尺寸运算

roundness：圆形

roundness 圆度 | roundness 圆形 | round-off accumulator 舍入误差累加器

roundness：圆

roundly 圆圆地 | roundness 圆 | roundsman 巡视者

prismatic roundness：棱圆度

true to tradition 名不虚传地 | prismatic roundness 棱圆度 | flexible shifting group plan 弹性分组制