return bend

return bend的基本解释

-

[化] 回弯头, 回管

与return bend相关的网络例句 [注：此内容来源于网络，仅供参考]

The invention orginates from the fact that most of the concrete reinforcement loops needed in practice can be divided up into relatively small number of types of loops which are characterized by a predetermined sequence of points of bend with a fixed sense of direction and amount of the angle of bend, in which case the loops of the same type differ from one another only in the lengths of the individual sides of the loops between the points of bend, or from one end of the loop to the first point of bend, and from the other end of the loop to the last point of bend.

问题补充：不要软件翻译的，最好自己翻译，起码通顺的这项发明orginates的是钢筋混凝土的循环需要在实践中最可分为相对的，是由弯曲点的序列特征与预定的方向和角度的数额固定感循环类型的为数甚少的事实弯曲，在这种情况下，同类型的循环，从彼此的不同只是在弯道之间，或从一个循环结束第一点弯曲点的循环个人边长，从另一端循环的最后一点弯曲。

Caused by disc brake on the brake Wheel Cylinder could not return to places 4 possible: First, 5 foot brake valve exhaust port blocking, high-pressure gas instinct platoon atmosphere, caused by gas-liquid master cylinder of the spring could not return to place, resulting in the system move oil, brake disc brake Wheel Cylinder Piston top dead and could not return to places; second is to the disc brake master cylinder gas-liquid pipeline blockage, resulting in brake Cylinder piston can not return to place; third master cylinder of the gas-liquid Spring itself can not return to position, brake fluid under high pressure gas can not return Axial pump to gas-liquid master cylinder reservoir chamber, resulting in brake Cylinder piston can not return to places; Fourth Wheel Cylinder piston disc brake system, due to moving fluid dirty or rusty card dead and can not return to the piston position.

造成盘式制动器上的制动分泵不能回位有4种可能：一是脚制动阀5的排气口堵塞，高压气体本能排人大气，造成气液总泵的弹簧不能回位，导致制动油将盘式制动器的制动分泵活塞顶死而不能回位；二是气液总泵至盘式制动器的油管堵塞，造成制动分泵活塞不能回位；三是气液总泵的弹簧本身不能回位，制动液在高压气体作用下，不能回到气液总泵的储油室，从而造成制动分泵活塞不能回位；四是盘式制动器制动分泵活塞由于制动液太脏或活塞生锈卡死而不能回位。

Furthermore, loss and crosstalk characteristics of bend intersections formed by sine bend, cosine bend and arc bend are compared.

在此基础上，对由正弦弯曲、余弦弯曲以及圆弧弯曲三种弯曲波导构成的SOI交叉波导的损耗及串扰特性进行了分析比较。

与return bend相关的网络解释 [注：此内容来源于网络，仅供参考]

return bend：回转弯头

return bend U形弯头回弯管回转弯头 | return bend 回转弯头 | return bent pipe 回弯管

return bend：回弯管

限制吃水船 restricted draft vessel | 回弯管 return bend | 骑肋骨 rider frame

return bend：回弯头

扩大表面管 extended surface tube | 回弯头 return bend | 管群间连接管 crossover

return bend：弯接头,U形接头

电阻器 resistor | <>弯接头,U形接头 return bend | 回路(电) return circuit

Return Bend U：型管

reducing tee 异径三?? | Return Bend U型管 | slip spade 插盲板: